Fujitsu MB91460 SERIES User Manual
Hide thumbs
Also See for MB91460 SERIES:
- Application note (77 pages) ,
- Getting started (41 pages) ,
- User manual (1038 pages)
Related Manuals for Fujitsu MB91460 SERIES
Summary of Contents for Fujitsu MB91460 SERIES
- Page 1 Fujitsu Microelectronics Europe FMEMCU-UG-910053-16 User Guide MB91460 SERIES EVALUATION BOARD SK-91467R-176PMC USER GUIDE...
-
Page 2: Revision History
V1.3 OGL - Updated figure 2-1 default jumper settings 2007/11/05 V1.4 OGL – Updated mode setting definitions, programming flow 2007/12/27 V1.5 OGL – removed wrong head line 2008/04/21 V1.6 MHz – corrected programming settings This document contains 45 pages. FMEMCU-UG-910053-16 - 2 - © Fujitsu Microelectronics Europe GmbH... -
Page 3: Warranty And Disclaimer
Product or parts thereof, if the Product is returned to Fujitsu Microelectronics Europe GmbH in original packing and without further defects resulting from the customer’s use or the transport. -
Page 4: Table Of Contents
External Bus Connectors (X13, X14) ..............33 5 PROGRAMMING THE INTERNAL FLASH..............35 Asynchronous Mode ....................35 Synchronous Mode ....................38 6 PROGRAMMING SWB MONITOR DEBUGGER ............39 7 APPENDIX ........................40 FMEMCU-UG-910053-16 - 4 - © Fujitsu Microelectronics Europe GmbH... - Page 5 SK-91467R-176PMC User Guide Contents Related Products ....................40 Information in the WWW ..................41 Tables ........................42 Figures ........................43 Abbreviations ......................44 © Fujitsu Microelectronics Europe GmbH - 5 - FMEMCU-UG-910053-16...
-
Page 6: Overview
Chapter 1 Overview 1 Overview 1.1 Abstract The SK-91467R-176PMC is a multifunctional evaluation board for the Fujitsu 32-bit FR60 Flash microcontroller series MB91460. It can be used stand-alone for software development and testing or as a simple target board to work with the emulator system. -
Page 7: Features
SK-91467R-176PMC User Guide Chapter 1 Overview 1.2 Features < Supports Fujitsu’s MB91F467R MCU in FPT-176P-M07 package or the MB2198 Emulator System with the Probe Cables EMA-MB91F467R-NLS-176M07 and EMA- MB91F467R-LS-176M07 < 9-12V unregulated external DC power supply < 5V, 3.3V, 2.5V and 1.8V onboard switching mode voltage regulators <... -
Page 8: General Description
Furthermore, all signals of the external bus interface are connected to a 96+48-pin VG connector to interface e.g. external graphic sub-boards such as Fujitsu’s ‘Jasmine’ sub-board. 1.3.5 Power Supply... - Page 9 Do not screw the cover too tight (max 0.054 Nm). If you have connectivity problems then please loosen the screws and tighten again the screws equally. Do not clean NQPACK, YQPACK, and YQSOCKET with steam. Cleaning material will contaminate inside of connector. © Fujitsu Microelectronics Europe GmbH - 9 - FMEMCU-UG-910053-16...
-
Page 10: Installation
After power on, the ‘Reset’-LED of the emulator must be off and the ‘Vcc’-LED must be on. If the Reset LED is still lit, check the settings of the emulator system and the power supply of the evaluation board. FMEMCU-UG-910053-16 - 10 - © Fujitsu Microelectronics Europe GmbH... -
Page 11: Default Jumper Settings For Mb91467R
JP63 LIN6: Enable Jumper 2 pin Open M 13 2 / 3 JP64 LIN6: Jumper 3 pin L 13 2 / 3 JP65 LIN6: Master Jumper 2 pin Open M 14 © Fujitsu Microelectronics Europe GmbH - 11 - FMEMCU-UG-910053-16... - Page 12 UART4: DTR/RTS Jumper 3 pin Open 2 / 3 JP98 UART4: RTS-CTS Jumper 2 pin Closed 2 / 3 JP99 LIN 4: VBat Jumper 2 pin Open Table 2-1: Jumper Settings FMEMCU-UG-910053-16 - 12 - © Fujitsu Microelectronics Europe GmbH...
-
Page 13: Jumper Location
The following picture shows the silk plot of the starter-kit with marked default jumper settings. The following picture shows the silk plot of the starterkit with marked default jumper settings. Figure 2-1: Default Jumper Settings © Fujitsu Microelectronics Europe GmbH - 13 - FMEMCU-UG-910053-16... -
Page 14: Software Installation
2.4 Software Installation 2.4.1 Installation of Softune Workbench With the “SK-91467R-176PMC” Fujitsu supplies a full working development environment called Softune Workbench V6. To develop own software the Softune Workbench development environment must be installed first. Follow the instructions for successful installation of the Softune Workbench. -
Page 15: Jumpers And Switches
1 (high) S1/4 (MD0) OFF (open) 0 (low) Table 3-1-1: default MCU Operating Mode MD3 MD2 MD1 MD0 DIP-Switch S1 (default setting) Figure 3-1-1: MCU mode switch for single chip run © Fujitsu Microelectronics Europe GmbH - 15 - FMEMCU-UG-910053-16... - Page 16 With P15_2 and P15_3 you can set the communication mod for the serial programming. P15_2 P15_3 Function 0 (low) 0 (low) asynchronous 0 (low) 1 (high) synchronous 1 (high) forbidden Table 3-3-2-1: Communication mode for serial programming FMEMCU-UG-910053-16 - 16 - © Fujitsu Microelectronics Europe GmbH...
-
Page 17: Power Supply (S3, Jp: 8, 9, 11, 12, 66)
MCU IO Block 3/ Peripherals @ 3.3V (VCC_3 3.3V/5V) 2 - 3 MCU IO Block 3/ Peripherals @ 5V Closed Power supply VCC_1 connected to MCUVCC5_1 Open Power supply VCC_1 connected (VCC5_1) MCUVCC5_1 © Fujitsu Microelectronics Europe GmbH - 17 - FMEMCU-UG-910053-16... - Page 18 (VBAT) Open No voltage supply to Vs of LIN Table 3-5: Power Supply Configuration By default, all Board supplies are set to 5V. +3.3V +2.5V +1.8V Figure 3-3: Voltage Test Pins FMEMCU-UG-910053-16 - 18 - © Fujitsu Microelectronics Europe GmbH...
- Page 19 SK-91467R-176PMC User Guide Chapter 3 Jumpers and Switches Regulator Test Pin Voltage 5.0 V 3.3 V 2.5 V 1.8 V Table 3-6: Voltage Test Pins © Fujitsu Microelectronics Europe GmbH - 19 - FMEMCU-UG-910053-16...
-
Page 20: Analog Power Supply Voltage (Jp: 9, 8, 10)
If JP8 and JP9 are open, the user has to supply an adequate analog voltage supply (AVcc and AVss) to the A/D-converter. If JP10 is open, the resistors R4 and R6 define AVRH. By default the resistor network (R4, R6) is not mounted on the board. FMEMCU-UG-910053-16 - 20 - © Fujitsu Microelectronics Europe GmbH... -
Page 21: Lin / Uart Connectors (X2 - X5)
(LIN VBbat) Open Pin 1 (LIN Vs) of X4 is not connected to Vin Table 3-8: UART 4 Settings By default, UART4 is connected to X4 and configured as RS232 interface. © Fujitsu Microelectronics Europe GmbH - 21 - FMEMCU-UG-910053-16... - Page 22 (LIN VBbat) Open Pin 1 (LIN Vs) of X3 is not connected to Vin Table 3-9: UART 5 Settings By default, UART5 is connected to X3 and configured as RS232 interface. FMEMCU-UG-910053-16 - 22 - © Fujitsu Microelectronics Europe GmbH...
- Page 23 (LIN VBbat) Open Pin 1 (LIN Vs) of X5 is not connected to Vin Table 3-10: UART 6 Settings By default, UART6 is connected to X5 and configured as RS232 interface. © Fujitsu Microelectronics Europe GmbH - 23 - FMEMCU-UG-910053-16...
- Page 24 Pin 1 (LIN Vs) of X2 is not connected to Vin Table 3-11: UART 0 Settings By default, UART0 is connected to X2 and configured as RS232 interface. For Flash programming, UART0 has to be used (RS232). FMEMCU-UG-910053-16 - 24 - © Fujitsu Microelectronics Europe GmbH...
-
Page 25: Can Interfaces (X7+X10)
Open this jumper if no external Reset shall be generated. In this case only the internal reset is active (e.g.: power-on) JP50 This solder jumper selects the third voltage monitored by the reset IC (1.8V and 2.5V are always monitored). © Fujitsu Microelectronics Europe GmbH - 25 - FMEMCU-UG-910053-16... - Page 26 If JP51(DTR sel) is set, one of the RST jumpers (JP60, 70, 80, 90) and the according DTR/RTS jumper have to be set, too. If the reset LED is steadily on, check the power supply input voltage and the settings for the reset-generation by UART and JP51. FMEMCU-UG-910053-16 - 26 - © Fujitsu Microelectronics Europe GmbH...
-
Page 27: User Buttons Sw1, Sw2, Sw3, Sw4, Sw5 (Jp: 11, 12, 13, 14, 15)
Pin 28 (NMIX) of the MCU is connected to “SW5” JP15 (SW5) Open No connection to the microcontroller Table 3-14: User Push Buttons Default: JP11, 12, 13, 14, 15 closed By default, all push-buttons are connected to the microcontroller. © Fujitsu Microelectronics Europe GmbH - 27 - FMEMCU-UG-910053-16... -
Page 28: Memories (Sram/Flash)
(Flash Enable) Flash is disabled SRAM is enabled JP44: (SRAM Enable) SRAM is disabled closed MCLKO connected to MCKLI JP46: (MCLKO=MCKLI) open MCLKO not connected to MCKLI Table 3-15: Flash/SRAM setting FMEMCU-UG-910053-16 - 28 - © Fujitsu Microelectronics Europe GmbH... -
Page 29: Connectors
45 – 88 89 – 132 133 – 176 The odd pin numbers are located on the one side and the even pin numbers are located on the other side of the connector. © Fujitsu Microelectronics Europe GmbH - 29 - FMEMCU-UG-910053-16... -
Page 30: Lin-Uart Connectors (X2-X5)
Description Not used CANL LOW-level CAN voltage input/output Ground Not used Not used Not used CANH HIGH-level CAN voltage input/output Not used Not used Shield Ground Table 4-2: CAN Connector Signals FMEMCU-UG-910053-16 - 30 - © Fujitsu Microelectronics Europe GmbH... -
Page 31: User-Leds
(Port 28), the resistor network RN1 can be removed. The following control signals are provided: Figure 4-4: User LEDs Port 28_7 28_6 28_5 28_4 28_3 28_2 28_1 28_0 Table 4-3: User LEDs © Fujitsu Microelectronics Europe GmbH - 31 - FMEMCU-UG-910053-16... - Page 32 P13_2 Select communication mode Not used Mode Pin2 INITX MCU reset signal SIN0 UART0 receive data SOT0 UART0 transmit data SCK0 UART0 clock Not used Ground Table 4-4: In-circuit programming connector FMEMCU-UG-910053-16 - 32 - © Fujitsu Microelectronics Europe GmbH...
-
Page 33: External Bus Connectors (X13, X14)
P29_5 P29_5 P16_6 P16_6 P29_7 P29_7 2.5V 2.5V Table 4-5: VG96 (X13) Signals Note: The pin numbers of the VG connectors refer to the male connectors, that plugs into the Starterkit. © Fujitsu Microelectronics Europe GmbH - 33 - FMEMCU-UG-910053-16... - Page 34 4.6.3 Distance between VG-Connectors To connect own applications to the Starterkit the following figure shows the distance between the VG DIN 41612 connectors. 8,89mm/ 350mil Figure 4-6: Layout of DIN VG Connectors: FMEMCU-UG-910053-16 - 34 - © Fujitsu Microelectronics Europe GmbH...
-
Page 35: Programming The Internal Flash
SIN0 is connected to RS232 transceiver (RXD) JP82 SOT0 is connected to RS232 transceiver (TXD) JP86 X2 Pin4/6 is connected to RS232 transceiver (T1out) (RS232/LIN) Table 5-1: Jumper Settings for Programming © Fujitsu Microelectronics Europe GmbH - 35 - FMEMCU-UG-910053-16... - Page 36 5) Choose the microcontroller device (“MB91F467R”) as device type and browse to the mhx-file you want to program to the embedded flash memory of the microcontroller. Press the button “Automatic Mode” to start programming. 6) Immediately reset the microcontroller. FMEMCU-UG-910053-16 - 36 - © Fujitsu Microelectronics Europe GmbH...
- Page 37 MCU manually immediately after pressing the button “Automatic Mode”. Figure 5-2: Reset Signal Settings © Fujitsu Microelectronics Europe GmbH - 37 - FMEMCU-UG-910053-16...
-
Page 38: Synchronous Mode
1 2 n/c n/c 3 4 n/c RST 5 6 SIN0 X1: Flash programming socket SOT0 7 8 SCK0 VCC 9 10 GND Figure 5-4: Flash Programming Socket FMEMCU-UG-910053-16 - 38 - © Fujitsu Microelectronics Europe GmbH... -
Page 39: Programming Swb Monitor Debugger
In case of successful startup of the monitor debugger and access to external SRAM the LED LD1, LD3 and LD7 are lit. Now connection to Softune Workbench can be started. © Fujitsu Microelectronics Europe GmbH - 39 - FMEMCU-UG-910053-16... -
Page 40: Appendix
< NQPACK176SD Socket for package FPT-176P-M07 (Tokyo Eletech Corp http://www.tetc.co.jp/e_products/e_nq_techdrawings.htm) < EMA-MB91F467R-NLS-176M07 Emulator probe cable for MB91F467R MCU < MB91460 Series < MB91V460 MB91460 Series Evaluation chip < MB91467R-176PMC Flash MCU FMEMCU-UG-910053-16 - 40 - © Fujitsu Microelectronics Europe GmbH... -
Page 41: Information In The Www
SK-91467R-176PMC User Guide Chapter 7 Appendix 7.2 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: http://emea.fujitsu.com/microelectronics Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://www.fme.gsdc.de/gsdc.htm... -
Page 42: Tables
Table 4-5: VG96 (X13) Signals ....................33 Table 4-6: VG48 (X14) Signals ....................34 Table 5-1: Jumper Settings for Programming ................ 35 Table 5-2: Jumper Settings for reset signal ................36 FMEMCU-UG-910053-16 - 42 - © Fujitsu Microelectronics Europe GmbH... -
Page 43: Figures
Figure 5-2: Reset Signal Settings ..................37 Figure 5-3: Successful Programming in Automatic Mode............38 Figure 5-4: Flash Programming Socket ................. 38 Figure 6-1: CS settings for SWB Monitor Debugger programming ........39 © Fujitsu Microelectronics Europe GmbH - 43 - FMEMCU-UG-910053-16... -
Page 44: Abbreviations
Controller Area Network Chip Select Fujitsu Microelectronics Europe GmbH Local Interconnect Network Microcontroller Unit Printed Circuit Board SRAM Static Random Access Memory SDRAM Synchronous Dynamic Random Access Memory UART Universal Asynchronous Receiver Transmitter FMEMCU-UG-910053-16 - 44 - © Fujitsu Microelectronics Europe GmbH... - Page 45 According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a 63225 Langen © Fujitsu Microelectronics Europe GmbH - 45 - FMEMCU-UG-910053-16...