Related Manuals for Jet JCDC-2
Summary of Contents for Jet JCDC-2
- Page 1 2.0 HP Mobile Cyclone Dust JCDC-2 Collector Original: Operating Instructions JPW (Tool) AG Tämperlistrasse 5 8117 Fällanden Switzerland Phone +41 44 806 47 48 +41 44 806 47 58 www.jettools.com M-717520M 2016-04...
- Page 2 CE-Conformity Declaration CE-Konformitätserklärung Déclaration de Conformité CE Product / Produkt / Produit: Dust Collector / Staubfänger / Collecteur de poussière JCDC-2 ( 717520M ) Brand / Marke / Marque: Manufacturer / Hersteller / Fabricant: JPW (Tool) AG, Tämperlistrasse 5, CH-8117 Fällanden...
-
Page 3: Warranty
Operating Instructions Dear Customer, Many thanks for the confidence you have shown in us with the purchase of your new JET-product. This manual has been prepared for the owner and operators of a JET JCDC-2.0 cyclone dust collector to promote safety during installation, operation and maintenance procedures. -
Page 4: Important Safety Instructions
Check for Do not use this dust collector for other than its alignment of moving parts, binding of moving intended use. If used for other purposes, JET parts, breakage of parts, mounting and any disclaims any real or implied warranty and other conditions that may affect its operation. - Page 5 24. Do not use to pick up anything that is burning dust, lint, hair, and anything that may reduce or smoking, such as cigarettes, matches or hot air flow. ashes. 32. Do not operate without hose connected to the 25. Do not use to pick up flammable inlet.
- Page 6 2.0 Direction / Safety Label Figure 1 Shows the general saftey rules to operate this machine Figure 2 Product Brand Logo Figure 3 Machine ID label : Shows the machine’s specifications and series number Figure 4 Warns user of hazardous voltage, and Figure 5 Warns user of heated hot surface should be open up by trained personnel only.
-
Page 7: Specifications
3.0 Specifications Model number ............................JCDC-2 Stock number .............................. 717520 Motor and electricals: Motor type ................ .totally enclosed fan cooled, induction, capacitor start Horsepower ........................... 2 HP (1.5kW) Phase ................................single Voltage ..............................230V only Cycle ................................50Hz Listed FLA (full load amps) ........................... 10 A Start capacitor .......................... - Page 8 Shipping weight, approximate ..................... 235 lb. (107 kg) The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.
-
Page 9: Setup And Assembly
Do not discard carton or packing material until dust collector is assembled and running satisfactorily. 4.2 Shipping contents – JCDC-2 Main carton (see Figure 1) Main housing – A Funnel – B Base –... -
Page 10: Tools Required For Assembly
4.3 Tools required for assembly Hex keys, 4mm and 5mm (provided) Open-end wrench, 10/12mm (provided) Cross-point (Phillips) screwdriver 4.4 Assembly Install four casters (L) to base (C) with pan head screws (HP1). See Figure 3. Install left and right stands (D ) to base (C) with flange head screws (HP8). - Page 11 Main housing is heavy. Two-person lift, or use hoist. Position main housing (A) between left and right stands (D ), and secure with flange head screws (HP2). See Figure 5. Figure 5 Install funnel (B) beneath main housing. Secure with funnel clamp (G). See Figure 6. Tighten screw on funnel clamp securely.
- Page 12 Figure 7 Install handle assembly (O) to canister filter (E) using set screw and nut. See Figure 8. Figure 8 10. Place gasket (X) between canister filter and main housing. Install canister filter onto main housing, and tighten with flange head screws (HP8) and nuts (HP9). See Figure 9. Figure 9 11.
- Page 13 12. Install inlet adaptor (I) on main housing and secure with pan head screw (HP1). 13. Apply foam tape (W) just above lower lip of canister filter. The foam tape should completely encircle the canister filter. 14. Install collection bag (P) to bottom of canister filter and secure with steel bag clamp (X). Figure 10 15.
- Page 14 Figure 12 The bag frame maintains the shape of the bag in the negative-pressure environment of the cyclone drum. Assemble bag frame as follows: 18. Screw the short and long frame supports into the hoops in alternating manner, as shown in Figure 13. Secure with sixteen pan head screws and hex nuts (HP10,HP11).
-
Page 15: Electrical Connections
Figure 14 5.0 Electrical connections All electrical connections must be done by a qualified electrician in compliance with all local codes and ordinances. Failure to comply may result in serious injury. Mains connection and any extension cords used must comply with applicable regulations. The mains voltage must comply with the information on the machine license plate. -
Page 16: Remote Controller
6.0 Operations 6.1 Start/stop Press green start button (A, Figure 15) to start dust collector. Press red stop button (B) to stop. The stop button (B) remains engaged after being pushed. To restart dust collector, rotate stop button clockwise to disengage. Figure 15 6.2 Remote controller The RF (radio frequency) remote controller operates on 2 AA batteries (included). -
Page 17: User Maintenance
If an inlet port is not being used, it should remain capped. An open port will diminish the machine’s efficiency, and may create a safety hazard. Contact your nearest JET distributor for a line of Dust Collector hoses and accessories. You can customize your installation and obtain maximum performance with dust hoods, hoses, clamps, fittings, and blast gates. -
Page 18: Optional Accessories
8.0 Optional accessories Part no. Description 717511 Canister collection bag for JCDC (package of 5) 717521 Drum collection bag for JCDC-2 (package of 5) Table 2 9.0 Troubleshooting the JCDC-2 9.1 Electrical and motor problems Symptom Possible Cause Correction* Motor will not start. -
Page 19: Performance Problems
9.2 Performance problems Symptom Possible Cause Correction Hose improperly secured at dust Inspect and remedy. origination point. Inlet port is open. Cap unused inlet ports. Collection bag is full. Empty bag (check sight window). Inspect drum for leaks, make sure lid is Collection drum not sealed properly.