Related Manuals for Aztec GUZZLER
Summary of Contents for Aztec GUZZLER
- Page 1 GUZZLER OWNER’S MANUAL PAGE 1 OWNER’S MANUAL THE GUZZLER High Speed Solution Retriever WWW.AZTECPRODUCTS.COM 215-393-4700 TOLL FREE: 800-331-1423 FAX: 215-393-4800 201 COMMERCE DRIVE, MONTGOMERYVILLE, PA 18936 12-2018...
-
Page 2: Table Of Contents
GUZZLER OWNER’S MANUAL PAGE 2 TABLE OF CONTENTS INTRODUCTION PG 3 SAFETY MESSAGES PG 4 IMPORTANT SAFETY INFORMATION PG 4 RECEIVING THE GUZZLER PG 4 GUZZLER SET UP PG 4 GUZZLER OPERATION PG 5 GUZZLER CLEAN UP PG 6 TRANSPORTINGTHE GUZZLER... -
Page 3: Introduction
All information in this Owner’s Manual is up to date and based on the latest product information available at the time of printing. Aztec Products, Inc. reserves the right to make changes at any time without notice or incurring obligation. Visit the website for an updated Owner’s Manual: www.aztecproducts.com. -
Page 4: Important Safety Information
Recommended surfaces for the Guzzler include: ➢ Vinyl and ceramic tile ➢ Sealed or finished concrete floors ➢ Wood, stone and terrazzo The Guzzler is not recommended for any other use. Call Aztec (800) 331-1423 for additional application questions. All of Aztec’s machines proudly MADE USA. -
Page 5: Guzzler Operation
3.) A normal walking speed assures nominal performance. The faster you go, the better the machine works. If the pump stops working, see TROUBLESHOOTING on pg 8. When foam escapes through breather hole in lid, tank is full (35 gallons) and must be emptied. See GUZZLER CLEAN UP below. -
Page 6: Guzzler Clean Up
Never lift tank by gripping the lid retainer ring. The Guzzler should be transported with the front swivel caster on the ground. The chassis should be in the “up” or transport position. When moving from site to site, DO NOT drag squeegee across parking lots or thresholds. -
Page 7: Guzzler Maintenance
REPAIRING LEAKS Isolate leak: Fitting Leak — Remove fitting, clean and smooth the surface and/or gasket. Apply silicon and re-install. Body Leak — Contact Aztec Products, manufacturer. Figure 1: Correct squeegee profile Figure 2: Pump plate clearance to floor 12-2018... -
Page 8: Troubleshooting And Notes
GUZZLER OWNER’S MANUAL PAGE 8 TROUBLESHOOTING Problem: NOT LEAVING FLOOR DRY Solution: Remove debris collected between the floor and the squeegee. Put debris in tank. Wipe squeegee of any debris. Adjust squeegee up or down to obtain optimum performance. See MAINTENANCE on pg 7. -
Page 9: Guzzler Underside Parts
GUZZLER OWNER’S MANUAL PAGE 9 GUZZLER PARTS DIAGRAM – UNDER SIDE ITEM # PART # DESCRIPTION 156-EY459 2" Swivel Caster 150-I7101 1 1/2 Gate Valve 156-2-4056-445 4" Swivel Caster 156-XA-08251-12 8" Wheel 307-72-9002 Wheel Driver Tab 015-62-644 Squeegee Assembly 016-71-9015... -
Page 10: General Guzzler Parts
GUZZLER OWNER’S MANUAL PAGE 10 GENERAL GUZZLER PARTS DIAGRAM ITEM # PART # DESCRIPTION 647-60032 8" Lid 164-10071 5/16-18*2 Hex Adjusting Bolt 173-79-5589 Chassis Spring 164-10079 Center Adjust. Bolt 016-71-9500 Pump Assembly 164-22002 5/16-18 Hex Nut 285-74-9051 Handle S2-47 Tuff Flex Vacuum Hose (sold by the foot) 2.5 ft... -
Page 11: Return Goods Policy
If it is not, follow the above policy and depend on us to respond quickly and responsibly. PROTECT YOUR WARRANTY! Read this Owner’s Manual carefully; all questions regarding the care and safety of this equipment, please call AZTEC PRODUCTS: (800) 331-1423 12-2018... -
Page 12: Guzzler Warranty
Aztec Products, Inc. agrees, at its option, to repair or replace at its own expense any product or part(s) which examination proves to be defective in workmanship or materials provided that the purchaser notifies Aztec Products, Inc.