Page 2
DT-300™ Series Download Tool Operator Integration Guide Issue #4033-IGE-01-01 REVISION HISTORY Rev №. Date Reason for Update Comment 10/09/12 Initial Document 4/1/13 Display change International Compliance • RoHS Directives • CE Mark • FCC Directives See below. CE Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
DT-300™ Series Download Tool Operator Integration Guide R e v i s i o n 1 1 GENERAL INFORMATION Description • Technical Contact Information. This section provides a general overview of the DT-300™ “BlueWaveDX” Download Tool Device In order to make operation of this device easier and pictured in Figure 1.
DT-300™ Series Download Tool Operator Integration Guide 2 COMPONENT NAMES Figure 2 illustrates the DT-300™ Functional Component Part Names and Locations. A. USB Connector Type A (Host) G. Power Switch B. LCD (Monochrome) H. SD Card Slot C. OK Button I.
DT-300™ Series Download Tool Operator Integration Guide 4 PRECAUTIONS Caution: Do NOT touch or pull on the connecting Cables with wet hands; this may cause an electrical shock, equipment damage or both. 5. Do not redesign or disassemble the Type 1 Type 2 Type 3...
DT-300™ Series Download Tool Operator Integration Guide 6 INSTALLATION Battery Installation Perform the following steps to install Batteries into Space the DT-300™ Device: Figure 6 Model Name Creation 1. Push the two (2) Tabs of the Battery Cover in the NOTE: Up to twenty (20) Folders can be direction of the Arrow illustrated in Figure created on an SD Card.
DT-300™ Series Download Tool Operator Integration Guide 3. When removing the SD Card from the DT-300™, 2. Connect the USB Cable B or Mini-B terminal to push in on the SD Card in the insertion direction the Validator’s USB Port (See Figure 9 b). once and then pull the SD Card out of the DT- NOTE: Refer to “Compatibility”...
DT-300™ Series Download Tool Operator Integration Guide press the to select it (See Figure 12). Screen once the Download Complete [“M:” indicates the “Model Name” and “V:” indi- is pressed. or the cates the “Version”.] NOTE: The DT-300 screen can display up to (20) files using the UP DOWN key.
DT-300™ Series Download Tool Operator Integration Guide Enabling a Denomination Function To view/display the Denomination Table, proceed as follows: 1. Turn the DT-300™ Power Switch ON and an SD Card check will begin (See Figure 23). Figure 21 Acceptance Log Reading Screen 5.
DT-300™ Series Download Tool Operator Integration Guide Error Message Function To receive/display the error condition from the Validator, proceed as follows: 1. Turn the DT-300™ Power Switch ON, and the SD Card check will begin (See Figure 27). Figure 32 Function Selection Screen 5 3.
DT-300™ Series Download Tool Operator Integration Guide 4. Press the to display the Maintenance Request Indication Screen. Press the to return to the previous Function Selection Screen. Figure 42 Standby Screen 5 The LCD Screen will display a Progress Bar during the Acceptance Log reading process as shown in Figure 43.
DT-300™ Series Download Tool Operator Integration Guide Table 9 Acceptance Logs Available (Continued) NOTE: The Firmware File should be newer than the current Firmware Version Screen Description presently in the DT-300. Total Ticket 2. Turn the DT-300™ Power Switch ON while Acceptance Rate pressing the and the...
DT-300™ Series Download Tool Operator Integration Guide Table 11 lists the various Battery Condition Dis- plays. Table 11 Battery Condition Indication Display Condition Figure 52 EEPROM Update Progress Bar Battery FULL 4. Once the update is complete, the LCD Screen will display the “...
DT-300™ Series Download Tool Operator Integration Guide Table 14 Received Log Files (Continued) ACKLIGHT ONTROL The DT-300™ Device contains the following Back- Item Description light Control Functions: Binary Format File written Log Information. File Contents Save the Data received from the Device The Backlight is always lit.
DT-300™ Series Download Tool Operator Integration Guide 8 UNIT DIMENSIONS DT-300 E NTIRE UTSIDE IMENSIONS Figure 55 illustrates the DT-300™ entire Unit outside dimensions. All Dimension are in Millimeters Figure 55 DT-300 Download Tool Outside Dimensions 9 COMPATIBILITY Table 18 lists the Validator Types compatible with the “BlueWaveDX” DT-300™ Device. Refer to the Column to create the proper compatible Validator's ...
DT-300™ Series Download Tool Operator Integration Guide 11 INTERNATIONAL COMPLIANCE RoHS Directives • CE Mark • FCC Directives • CE Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the User may be required to take adequate measures.
DT-300™ Series Download Tool Operator Integration Guide 12 TECHNICAL CONTACT INFORMATION To obtain further Technical Information regarding the DT-300™ Device, please contact the closest office listed below: & O CEANIA MERICA JCM G (HK) L JCM A MERICAN Phone: +852-2429-7187 Phone: +1-702-651-0000 Fax: +852-2929-7003 Fax: +1-702-644-5512...
DT-300™ Series Operator Integration Guide Index 13 INDEX Cautions Safety special boxed areas providing important safty Pictographs indicating … … information 1 to 3 symbols inside boxed area Contact Information Special Notes … Address and Telephone Numbers for italic text highlights …...