Summary of Contents for Feig Electronic OBID Classic-Pro Series
Page 1
MONTAGE ® OBID classic-pro INSTALLATION ID CPR50.10-xE (-E / -SE / -RE / -SRE) RFID Reader for ISO/IEC14443-A & -B, NFC and ISO/IEC15693 with Ethernet Interface (deutsch / english) preliminary public (B) 2009-10-07 M90701-1de-ID-B-FCC.doc...
Page 2
® OBID classic-pro Montage ID CPR50.10-E/-RE FEIG ELECTRONIC GmbH Seite 2 von 39 M90701-1de-ID-B-FCC.doc...
Page 3
® OBID classic-pro Montage ID CPR50.10-E/-RE deutsche Version ab Seite 4 english version from page 22 FEIG ELECTRONIC GmbH Seite 3 von 39 M90701-1de-ID-B-FCC.doc...
Page 4
Hinweise jederzeit dankbar. Die in diesem Dokument gemachten Installationsempfehlungen gehen von günstigsten Rahmenbedingun- gen aus. FEIG ELECTRONIC GmbH übernimmt weder Gewähr für die einwandfreie Funktion in system- fremden Umgebungen, noch für die Funktion eines Gesamtsystems, welches die in diesem Dokument be- schriebenen Geräte enthält.
4.2.1. EMV-Beeinflussung über Zuleitungen .................17 4.2.2. EMV-Beeinflussung über magnetische Felder ............17 5. Technisch Daten ID CPR50.10-E/-RE 5.1. Zulassung ..........................19 5.2. Europa (CE)........................19 5.3. Declaration of Conformity for USA..................19 5.4. Declaration of Conformity for CANADA................20 5.5. Abmessungen........................21 FEIG ELECTRONIC GmbH Seite 5 von 39 M90701-1de-ID-B-FCC.doc...
Obwohl dieses Gerät die zulässigen Grenzwerte für elektromagnetische Felder nicht ü- berschreitet, sollten Sie einen Mindestabstand von 25 cm zwischen dem Gerät und Ih- rem Herzschrittmacher einhalten und sich nicht für längere Zeit in unmittelbarer Nähe des Geräts bzw. der Antenne aufhalten. FEIG ELECTRONIC GmbH Seite 6 von 39 M90701-1de-ID-B-FCC.doc...
Schneidschraube, Senkkopf 3,2 x 15 mm zur Montage von Gehäuseunterteil auf Aufputzadapter Schneidschraube, Senkkopf Schneidschrauben 3,2 x 25 mm zur Wandmontage Montageanleitung 2.1. Optionales Zubehör ID CPR.I/O-A: Extension Board mit einem Relais und zwei digitalen Eingängen FEIG ELECTRONIC GmbH Seite 7 von 39 M90701-1de-ID-B-FCC.doc...
Alternativ kann der Reader ID CPR50.10-RE mit einem internen Relais verwendet werden. ID CPR.IO Door Contact ID CPR50.10-E Ethernet PoE Power Supply (IEEE802.3af) Ethernet Abbildung 1:Installation für ID CPR50.10-E mit optionalem I/O Extension Board ID CPR.I/O-A FEIG ELECTRONIC GmbH Seite 8 von 39 M90701-1de-ID-B-FCC.doc...
Der räumliche Abstand zu benachbarten Lesern gleicher Bauart sollte 30 cm nicht unter- schreiten. • Vor der endgültigen Installation sollte der geplante Installationsort auf seine Tauglichkeit geprüft werden. Abbildung 2: Aufputzadapter Abbildung 3: Unterputzgehäuse Montageausrichtung, Montageausrichtung, (⇑ TOP) nach oben (⇑ TOP) nach oben FEIG ELECTRONIC GmbH Seite 9 von 39 M90701-1de-ID-B-FCC.doc...
Page 10
• Gehäuse von unten mit Schraube Torx 3x8 mm (Torx T10) verschließen. • Schutzfolie von Frontscheibe entfernen. Abbildung 4: Rückansicht mit eingerasteter Anschlussplatine (1) Abbildung 5: Gehäusedeckel stecken Abbildung 6: Gehäusedeckel öffnen FEIG ELECTRONIC GmbH Seite 10 von 39 M90701-1de-ID-B-FCC.doc...
DC – für ID CPR.I/O-A * Die Versorgung über ein externes Netzteil ist nicht notwendig wenn der Reader über ein PoE-Netzteil versorgt wird, in dem Fall bleiben die Anschlüsse VIN-Ext+ und GND-EXT- frei. FEIG ELECTRONIC GmbH Seite 12 von 39 M90701-1de-ID-B-FCC.doc...
ID CPR50.10-E/-RE 4.1.3. Anschluss über PoE Netzteil In diesem Verdrahtungsbeispiel wird der Reader über ein PoE Netzteil mit Spannung versorgt. ID CPR.IO Door Contact ID CPR50.10-E Ethernet PoE Power Supply (IEEE802.3af) Ethernet FEIG ELECTRONIC GmbH Seite 13 von 39 M90701-1de-ID-B-FCC.doc...
• Versorgungsspannungen außerhalb der Spezifikation können zur Zerstörung des Gerä- tes führen. • Im Falle von getakteten Netzteilen auf ausreichende Filterung der Versorgungsspannung achten. • Störungen der Versorgungsspannung können sich negativ auf die Lese- und Schreib- reichweite der Module auswirken. FEIG ELECTRONIC GmbH Seite 14 von 39 M90701-1de-ID-B-FCC.doc...
über die Klemmen 7 [NO], 8 [COM] und 9 [NC]. 4.1.5.2. Digitale Eingänge (ID CPR.I/O-A) Die digitalen Eingänge [IN1] und [IN2]) dürfen nur gegen Ground, Klemme [GND] geschaltet wer- den. Eine Beschaltung mit Fremdspannung kann zur Zerstörung des Gerätes führen! FEIG ELECTRONIC GmbH Seite 15 von 39 M90701-1de-ID-B-FCC.doc...
4.1.5.4. Spannungsversorgung des ID CPR.I/O-A Die Spannungsversorgung des externen I/O Moduls erfolgt ausschließlich über den Reader ID CPR50.10-E über die Anschlüsse VCC (+) und GND (-). Abbildung 10: Spannungsversorgung des ID CPR.I/O-A FEIG ELECTRONIC GmbH Seite 16 von 39 M90701-1de-ID-B-FCC.doc...
Feldes. Magnetische Wechselfelder in der Nähe der Antenne können sich negativ auf die Funktion des Readers auswirken. Zu den Quellen solcher magnetischen Störfelder gehören zum Beispiel Spulen innerhalb eines primär oder sekundär getakteten Netzteils. FEIG ELECTRONIC GmbH Seite 17 von 39 M90701-1de-ID-B-FCC.doc...
ID CPR50.10-E Ethernet 10BASE-T/100BASE-TX Interface automatik MDI/MDI-X cross over correction TCP/IP protocol EEPROM für Konfigurationsparameter (1 Million Schreibzyklen) NFC: Type 1, Type 2 and Type 4 in read/write and NFC card emulation mode FEIG ELECTRONIC GmbH Seite 18 von 39 M90701-1de-ID-B-FCC.doc...
- Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FEIG ELECTRONIC GmbH Seite 19 von 39 M90701-1de-ID-B-FCC.doc...
Usually this is followed by the following RSS caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FEIG ELECTRONIC GmbH Seite 20 von 39 M90701-1de-ID-B-FCC.doc...
ID CPR50.10-E/-RE 5.5. Abmessungen 84,2 mm 77,7 mm 56,8 mm 60,0 mm 60,0 mm Abbildung 11: Unterputzgehäuse Abbildung 12: Aufputzadapter Befestigungsmasse Befestigungsmasse 84,2 mm 40 mm 22 mm 14,0 mm Abbildung 13: Gehäuseabmessungen FEIG ELECTRONIC GmbH Seite 21 von 39 M90701-1de-ID-B-FCC.doc...
Page 22
FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed with components and testing methods for a level of reliability suitable for use in or in connection with surgical implants or as critical components in any life support systems whose failure to perform can reasonably be expected to cause significant injury to a human.
Page 23
8.2.2. EMC effects from magnetic fields ................35 9. Technical Data of the Reader Family ID CPR50.10-E/-RE 9.1. Approval..........................37 9.2. Europe (CE)........................37 9.3. Declaration of Conformity for USA..................37 9.4. Declaration of Conformity for CANADA................38 9.5. Dimensions ........................39 FEIG ELECTRONIC GmbH Page 23 of 39 M90701-1de-ID-B-FCC.doc...
25 cm between the device and your cardiac pace- maker and not stay in an immediate proximity of the device respective the antenna for some time. FEIG ELECTRONIC GmbH Page 24 of 39 M90701-1de-ID-B-FCC.doc...
Thread cutting screws 3,2 x 15 mm for mounting the surface adapter Thread cutting screw 3,2 x 25 mm for wall mounting Installation instruction 6.2. Optional Accessories ID CPR.I/O-A: Extension Board with one Relay and two digital Inputs. FEIG ELECTRONIC GmbH Page 25 of 39 M90701-1de-ID-B-FCC.doc...
Optionally the reader ID CPR50.10-RE with one internal relay can be used. ID CPR.IO Door Contact ID CPR50.10-E Ethernet PoE Power Supply (IEEE802.3af) Ethernet Fig. 1: Installation diagram for ID CPR50.10-E with optional I/O extension board ID CPR.I/O-A FEIG ELECTRONIC GmbH Page 26 of 39 M90701-1de-ID-B-FCC.doc...
Before any installation the intended position of the Reader should be tested for its suit- ability. Fig. 2 Surface adapter, Fig. 3 Concealed casing, Mounting direction, Mounting direction, (⇑ TOP) on top position (⇑ TOP) on top position FEIG ELECTRONIC GmbH Page 27 of 39 M90701-1de-ID-B-FCC.doc...
Page 28
• Remove the protection foil from the front part. Fig. 4 Backside view with the fitted connection board (1) Fig. 5 Fitting of the housing cover Fig. 6 Opening of the housing cover FEIG ELECTRONIC GmbH Page 28 of 39 M90701-1de-ID-B-FCC.doc...
Green Orange Rx D2+ Orange Striped Green striped BI D3+ Blue Blue BI D3- Blue Striped Blue Striped Rx D2- Orange Green BI D4+ Brown Striped Brown Striped BI D4- Brown Brown FEIG ELECTRONIC GmbH Page 29 of 39 M90701-1de-ID-B-FCC.doc...
* The power supply via an external power supply is not necessary if the reader is powered via PoE power supply. In that case the connection VIN-EXT+ and GND-EXT- are not used. FEIG ELECTRONIC GmbH Page 30 of 39 M90701-1de-ID-B-FCC.doc...
® OBID classic-pro Installation ID CPR50.10-E/-RE 8.1.3. Connection with PoE Supply ID CPR.IO Door Contact ID CPR50.10-E Ethernet PoE Power Supply (IEEE802.3af) Ethernet FEIG ELECTRONIC GmbH Page 31 of 39 M90701-1de-ID-B-FCC.doc...
• If switching power supplies are used with the module, be sure that there is adequate fil- tering. • Noise from the power supply can result in a reduction of the read/write range of the module. FEIG ELECTRONIC GmbH Page 32 of 39 M90701-1de-ID-B-FCC.doc...
7 [NO], 8 [COM] and 9 [NC]. 8.1.5.2. Digital inputs (ID CPR.I/O-A) The digital inputs [IN1] and [IN2] can only be connected to Ground, connector [GND]. Any connection to external voltage might damage the unit! FEIG ELECTRONIC GmbH Page 33 of 39 M90701-1de-ID-B-FCC.doc...
The power supply of the external I/O Module must be realized via the reader ID CPR50.10-E and the connection VCC (+) and GND (-). Fig. 10: Power supply of the ID CPR.I/O-A FEIG ELECTRONIC GmbH Page 34 of 39 M90701-1de-ID-B-FCC.doc...
Alternating magnetic fields in the vicinity of the antenna can have a negative influence on the reader function. Sources of such magnetic interference fields include coils within a primary or secondary switching power supply. FEIG ELECTRONIC GmbH Page 35 of 39 M90701-1de-ID-B-FCC.doc...
Ethernet 10BASE-T/100BASE-TX Interface automatic MDI/MDI-X cross over correction TCP/IP protocol EEPROM for configuration parameter (1 million write cycles) NFC: Type 1, Type 2 and Type 4 in read/write and NFC card emulation mode FEIG ELECTRONIC GmbH Page 36 of 39 M90701-1de-ID-B-FCC.doc...
- Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FEIG ELECTRONIC GmbH Page 37 of 39 M90701-1de-ID-B-FCC.doc...
Usually this is followed by the following RSS caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FEIG ELECTRONIC GmbH Page 38 of 39 M90701-1de-ID-B-FCC.doc...
84,2 mm 77,7 mm 56,8 mm 60,0 mm 60,0 mm Fig. 11 Concealed casing Fig. 12 Surface adapter Fixing dimensions dimensions 84,2 mm 22 mm 40 mm 14,0 mm Fig. 13 Housing dimensions FEIG ELECTRONIC GmbH Page 39 of 39 M90701-1de-ID-B-FCC.doc...