Line Out Jacks - Aiwa NSX-MT960 Operating Instructions Manual

CD DIGITAL OUT
(OPTICAL)
5.1 CH
VIDEO/AUX IN
INPUT
MD
LINE OUT
SUPER
WOOFER
Refer to the operating instructions of the connected equipment
for details.
The connecting cords are not supplied. Obtain the necessary
connecting cords.
Consult your local Aiwa dealer for optional equipment.
.s #
m.'!
w q
'w .,.% ~., ., ,, .
.W ,,.. b. ..,,= :,. ..-.., =. . . . ~,
-*,. 2!
w 8, ,+ # r
wwklw,.# *M*,-J !7! u ,'
r, m \*r% ,*
,&*=:- ..
VIDEO/AUX IN JACKS
This unit can input analog sound signals through these jacks.
Use a cable with RCA phono plugs to connect audio equipment
(turntables, LD players, VCRs, TV, MD players, etc.).
Connect the red plug to VIDEO/AUX IN R jack, and the white plug
to VIDEO/AUX IN L jack.
When connecting a turntable
Use an Aiwa turntable equipped with a built-in equalizer amplifier.
This jack is recommended to connect with an MD player.
Use a cable with RCA phono plugs.
Connect the red plug to MD R jack, and the white plug to MD L
jack.
When MD player is connected to these jacks, no sound will be
output from LINE OUT jacks.
-.? -
r ,.-: :%-- ,.% m-:=:. . ,-:= .,--:2:e2%$,. =-,.*: --------- % -,. % -%? . . .. .J-:~.~% -%'w~, ' -: .-,:*, ?.9'. % ~:-.. % ~
LINE OUT JACKS
This unit can output analog sound signal through these jacks.
Use a cable with RCA phono plugs to connect audio equipment
with LINE
IN
(analog input) jacks.
Connect the red plug of a cable to LINE OUT R jack, and the
white plug to LINE OUT L jack.
m
Do not connect an equipment to LINE OUT and VIDEO/AUX IN
simultaneously. Otherwise, noise is generated and malfunction
occurs
b a. = . . -,..} L.s,q,.: *,.,:, :.,:<.: .4.:...* ;. .,,,,. ,*,T*..,,.,W ,,,,,.= . . . . . ,- =.', . . . ,.,
.:!,"
..-%s. -.s.
!-%
,W., .! 'r..,.., . . .
CD DIGITAL OUT (OPTICAL) JACK
This unit can output CD digital sound signals through this jack.
Use an optical cable to connect digital audio equipment (digital
amplifier, DAT deck, MD recorder, etc.).
Remove the dust cap @ from CD DIGITAL OUT (OPTICAL)
jack. Then, connect an optical cable plug to CD DIGITAL OUT
(OPTICAL) jack.
This unit can input sound signals from the audio equipment
6
(DVD player, LD player, etc.) that contains a Dolby Digital decoder ~
with the 5.1 ch output terminals. Refer to "CONNECTING A DVD z
PLAYER" (page 27).
Q
1
To play equipment connected to VIDEO/AUX IN jacks or MD
jacks, proceed as follows.
1
Press VIDEO/AUX or MD.
2
To
play the equipment connected
to VIDEO/AUX: press
VIDEO/AUX once. "VIDEO appears on the display.
To play the equipment connected to MD: press MD. "MD
appears on display.
Play the connected equipment.
To
change a source name in the display
When VIDEO/AUX is pressed once, "VIDEO is displayed initially.
It can be changed to "AUX or "TV.
With the power on, press POWER while pressing VIDEO/AUX.
When the "5.1 ch IN" is displayed, press VI DEO/AUX again to
see the changed source name.
Repeat the procedure to select one of the names.
To
adjust the sound level of the external source
When the sound level of the external source is much higher or
much lower than that of other function sources, adjust it as follows.
1
Press VIDEO/AUX or MD and play the equipment.
2 Press ++ or ~ so that the sound level becomes the same
as that of other function sources.
During recording, the sound level can not be adjusted.
When the CD DIGITAL OUT (OPTICAL) jack is not being used
Attach the supplied dust cap.
ENGLISH 26