Page 1
M 1 6 5 - N 5 7 1 U - 0 0 2 HIGH PERFORMANCE Super Night Vision Camera OPER ATI ON MA NUAL T ha nk y ou f or ch o o sin g o u r h ig h q u a lit y ca m e r a . Be fore at t empt in g to co n n e ct o r o per a te , p le a se r e a d a n d f o llo w t hes e i nst ructi o n s.
C O NT E NT S 1. CAUTIONS 2. IMPORTANT SAFETY INSTRUCTION 3. COMPONENTS 4. NAME AND FUNCTION 5. INSTALLATION 6. DIMENSIONS 7. SPECIFICATION 8. OSD MANUAL...
Page 3
1 . C AUT IO N S This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. Th is device ma y n o t ca u se h a r m fu l in te r fe r e n c e . 2.
Page 4
1 . C AUT IO N S Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
2 . IMP O R TA NT S A FE T Y I NS T RU C T IO N 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth.
Page 6
3 . C OM PO N E NT S SUPER NIGHT VISION CAMERA SUNSHIELD VIDEO OUTPUT TEST CABLE L-WRENCH -2ea / SCREW(5x30L) - 3ea / SUNSHIELD FIXING BOLT OPERATION MANUAL...
4 . N AME A N D FU NC T I O N ③ ② ① ③ ④ ⑤ ⑧ ④ ④ ⑥ ⑦ ① Sun shie ld Fix ing B o lt External Zoom and Focus adjustment ② Sun shie ld After adjusting zoom and focus, to prevent water infiltration, firmly tighten the zoom and ③...
Page 8
5 . INS T AL LA TI O N • MOUNTING POSITION 360° 90° * 1st Axis * 2nd Axis 360° 15° * 3rd Axis...
Page 9
5 . INS T AL LA TI O N • MONITOR CONNECTION (1) DC12V DC 12V POWER SUPPLY DC12V VIDEO IN MONITOR BNC FEMALE (2) DUAL(DC12V/AC24V) DC 12V POWER SUPPLY or AC 24V POWER SUPPLY DC12V/AC24V VIDEO IN MONITOR When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.
Page 10
6 . D IM EN S I O N S Ø60 175.7 129.4 265.9 M12XP1.25 Ø80...
7 . SP ECI F I CA TI O N Signal Format NTSC Image Sensor 1/3” 960H SONY EXview HAD CCD II Scanning System 2 : 1 Interlace H Resolution. 750TV Lines Scanning Frequency 15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V) Total Pixels No. 1020(H) X 508(V) 1020(H) X 596(V) Effective Pixels No.
8 . OS D M AN UA L SETUP MENU (page 1) SHUTTER/AGC WHITE BAL SHUTTER/AGC BACKLIGHT PICT ADJUST AUTO MANUAL MOTION DETECTION NEXT (page2) RETURN EXIT SAVE ALL WHITE BALANCE BACKLIGHT PUSH USER 1 USER 2 ANTI CR RETURN MANUAL PUSH LOCK RETURN...
Page 13
8 . OS D M AN UA L SETUP MENU (page 2) PRIVACY DAY/NIGHT PRIVACY DAY/NIGHT CAMERA ID AREA SEL AUTO LANGUAGE COLOUR COLOUR CAMERA RESET TRANSP MOSAIC EXT1 EXT2 BACK (page 1) EXIT SAVE ALL RETURN RETURN CAMERA ID LANGUAGE CAMERA RESET NR MODE...
8 . OS D M AN UA L SHUTTER / AGC Modes: Auto, Manual Auto High Luminance Mode: Shut+Auto Iris, Auto Iris Brightness: 0 to 255 (increments of 1) (Adjusts the brightness of the image) Low Luminance Mode: AGC, Off (Auto Gain Control on or off) Brightness: x0.25, x0.50, x0.75, x1.00 (Sets the brightness/AGC level applied in low light conditions)
Page 15
8 . OS D M AN UA L WHITE BAL Modes: ATW, Push, User1, User2, Anti CR, Manual, Pushlock (Adjusts the white balance to suit area being viewed) ATW (Auto Trace White balance) Speed: 0 to 255 (increments of 1) (Adjusts the pull in speed of ATW) Delay Cnt: 0 to 255 (increments of 1) (Sets the time-based hysteresis of ATW)
8 . OS D M AN UA L PICT ADJUST Mirror: Off, on (horizontally inverts image). Brightness: 0 – 255 (increments of 1) Contrast: 0 – 255 (increments of 1) Sharpness: 0 – 255 (increments of 1) Hue: 0 – 255 (increments of 1) Gain: 0 –...
Page 17
8 . OS D M AN UA L PRIVACY PRIVACY: Allows upto 8 masks to be applied to the image (note that if motion area in motion det menu is set to ‘on’, this reduces to 4 privacy zones) Area Sel: 1 - 8 (Selects the motion detection area) Top: 0 –...
8 . OS D M AN UA L NR (2DNR) Digital noise reduction is used to remove ‘noise’ from the image in low light conditions when AGC is applied. NR mode : Off, Y, C, Y/C (Sets the 2D NR filter mode) Y Level: 0 –...
Need help?
Do you have a question about the KPC-N571U and is the answer not in the manual?
Questions and answers