Cv - Summery List - ZIMO MX638 Series Instruction Manual

Table of Contents

Advertisement

Non-Sound Decoder MX600 - MX638 and Sound Decoder MX640 - MX659
CV – Summary List
11
This list summarizes all CV's in numerical order, with very short descriptions (as a reminder). De-
tailed information can be found in the preceding chapters ("Configure", "ZIMO Sound").
The "red" column: Denotes the chapter the CV's belong to.
Chap-
CV
Denomination
Range
ter
1 – 127
3.4
#1
Short address
3.6
#2
Start voltage
1 - 255
3.7
#3
Acceleration rate
0 - 255
3.7
#4
Deceleration rate
0 - 255
3.6
#5
Top speed
0 - 255
3.6
#6
Medium speed
0 - 255
SW-Version
Read only
3.3
#7
Number
Manufacturer ID,
Read only 145
3.3
#8
Reset &Set
Motor control
1 - 255
3.6
#9
frequency
0 - 252
3.6
#10
Compensation
-
#11
------
-
#12
------
Analog functions
0 - 255
3.5
#13
F1...F8
Analog functions F0,
0 - 255
3.5
#14
F9...
-
#15
------
-
#16
------
#17,
3.4
Extended Address
128 -10239
18
0 – 127
Consist address
3.4
#19
Consist function F1 -
0 - 255
3.4
#21
F8
0 - 191
3.4
#22
Consist function F0
Acceleration
0 - 255
3.7
#23
variation
Deceleration
0 - 255
3.7
#24
variation
Default Description
The "short" (1-byte) loco address.
3
Internal speed step applied as lowest external speed
1
Multiplied by 0.9 equals' acceleration time.
(2)
Multiplied by 0.9 equals' deceleration time.
(1)
1
Internal speed step for highest external speed step.
(=255)
1
Internal speed step for medium external speed step
(=1/3 of #5)
Current firmware version number. For subversion see
-
CV #65.
Given by the NMRA. CV #8=8: Hard Reset.
(=ZIMO)
Tens digit for sampling rate, ones digit for sampling
55
time.
0
Internal speed step for reduced intensity per CV #113.
Select analog functions F1 (Bit 0), F2 (Bit 1)...
0
Select analog functions F0 forw (Bit 0), rev (Bit 1)...
0
The "long" (2-byte) addresses. Active only if Bit 5 in CV
0
#29 is set to 1.
0
Consist address for 2 or more engines, valid if >0
Consist functions F1 (Bit 0), F2 (Bit 1)...
0
0
Select consist functions F0 forw (Bit 0), rev (Bit 1)...
Temporary adaptation of CV #3 (Acceleration).
0
Temporary adaptation of CV #4 (Deceleration).
0
Chap-
CV
Denomination
Range
ter
-
#25
------
-
#26
------
Asymmetrical stops
0, 1, 2, 3
3.10
#27
(ABC)
RailCom
0 - 3
3.2
#28
Configuration
Basic settings
3.2
#29
0 - 63
NMRA Function map
3.14
#33
0 - 255
F0
NMRA Function map
3.14
#34
0 - 255
F0
#35-
Function mapp. F1 -
3.14
0 - 255
46
F12
-
#47
------
-
#48
------
0 - 255
3.9
#49
HLU acceleration
HLU deceleration
0 - 255
3.9
#50
#51
HLU speed limits
0 - 255
3.9
-
55
Motor regulation
0 - 255
3.6
#56
Voltage reference
0 - 255
3.6
#57
BEMF intensity
0 - 255
3.6
#58
HLU delay
0 - 255
3.9
#59
Dimming
0 - 255
3.18
#60
3.14
#61
ZIMO ext. mapping
1,2...97,98
3.21
#62
Effects modifications
0 - 9
Effects modifications
0 - 99
3.21
#63
3.21
#64
Effects modifications
0 - 9
Sub-Vers Number
Read only
3.3
#65
Page 71
Default Description
Bit 0 = 1: Stops if voltage in right rail, Bit 1 = 1: left rail
0
Bit 0 = 1: RailCom (Broadcast), Bit 1 = 1:RailCom Data
3
Bit 0 - Train direction: 0 = normal, 1 = reversed
14 =
Bit 1 - Speed steps: 0 = 14, 1 = 28
1
0000
110
Bit 2 - DC (analog): 0 = disabled, 1 = enabled
Bit 3 = 1
Bit 3 – RailCom: 0 = deactivated, 1 = activated
("RailCom"
is switched
Bit 4 - Speed table: 0 = 3-point, 1 = 28-point
on)
Bit 5 - Decoder address: 0 = CV #1, 1 = CV #17+18
Function mapping for F0 forward
1
Function mapping for F0 reverse
2
4,8,2,4,8,..
Function mapping for F1 ... F12
.
0
Multiplied by .4 equals acceleration time in seconds
0
Multiplied by .4 equals deceleration time in seconds
20, 40...
Speed steps for each of the 5 HLU speed limits
55
PID regulation: P-value (tens), I value (ones digit)
Absolute voltage in tenth of a volt: max motor speed,
0
= 0: relative to track voltage.
255
Intensity of back-EMF control at the lowest speed step.
5
Tenth of a second delay after receiving new HLU limit
Reduction of function output voltage with PWM
0
0
Configurations not covered by NMRA mapping
0
Change of minimum dimming value
51
Tens digit: cycle time, Ones digit: extends OFF time
5
Ditch light off-time modification
-
Supplement to main version noted in CV #7.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents