Sony 3-270-589-12 (1) Operating Instructions Manual page 100

VIDEO CONTROL [Video]: Settings related to video
control
WIDE MODE [> Wide
mode]: For SD input and
output, specify whether
to record and play back
with the addition of wide
picture information.
FRAME PB [> Frame PB]: Select whether to output fields or
frames as still images of video.
PROCESS CONTROL
[> Proc ctrl]: Separate
adjustment screens
appear for the following
items. Use the jog dial to
make settings, and press
the MENU button to
return from the
adjustment screens to
the second level of the
setup menu.
100
System Menu
INPUT [>> Input] (only when
the PDBK-104 option board is
installed)
OUTPUT [>> Output]
VIDEO GAIN [>> V gain]:
Adjust the video output
level.
CHROMA GAIN [>> C gain]:
Adjust the chroma output
level
CHROMA PHASE [>> C
phase]: Adjust the chroma
phase.
SETUP LEVEL [>> Setup
lev]: Adjust setup level.
HD SYNC PHAS [>> HD S
PHAS]: Adjust HD sync
phase.
SD SYNC PHAS [>> SD S
PHAS]: Adjust SD sync
phase.
OUTPUT SCH [>>
OutputSCH]: Adjust the
subcarrier H phase of
composite video output.
Description
*AUTO [>>> Auto]: Automatically record wide picture
information when it is detected in the selected input video
signal.
OFF [>>> OFF]: Do not record wide picture information.
ON [>>> ON]: Always record wide picture information.
*AUTO [>>> Auto]: When DOWN CONVERT >CONV MODE
in the setup menu is set to "SQUEEZE", automatically add
wide picture information when playing back MPEG HD-
format video. When playing back DVCAM-format video,
automatically add wide picture information if wide picture
information is detected on the disc.
OFF [>>> OFF]: Do not add wide picture information.
ON [>>> ON]: Always add wide picture information.
Notes
• To add wide picture information to the output signal, it is
necessary, in addition to setting this item, to set line 20
(when the system frequency is 60I, 30P) or line 23 (when the
system frequency is 50I, 25P) to "THROUGH" in the VIDEO
CONTROL >BLANK LINE item of the setup menu.
• When the system frequency is 60I or 30P, the VITC signal is
not output if the VITC insertion position has been set to
"20LINE" with the setup menu items TIME CODE >VITC
POS SEL-1/2.
*AUTO [>> AUTO]: Output a field image when the format is
interlaced, and output a frame image when the format is
progressive.
FRAME[>> FRAME]: Always output a frame image.
–848 [>>> –848] to 847 [>>> 847]
Factory default setting: *0 [>>> 0]
–848 [>>> –848] to 847 [>>> 847]
Factory default setting: *0 [>>> 0]
–128 [>>> –128] to 127 [>>> 127]
Factory default setting: *0 [>>> 0]
–272 [>>> –272] to 271 [>>> 271]
Factory default setting: *0 [>>> 0]
–2200 [>>> –2200] to 2199 [>>> 2199] (system frequency:
60i)
–2640 [>>> –2640] to 2639 [>>> 2639] (system frequency:
50i)
–2750 [>>> –2750] to 2749 [>>> 2749] (system frequency:
23.98P)
Factory default setting: *0 [>>> 0]
–1716 [>>> –1716] to 1715 [>>> 1715] (system frequency:
60i/23.98P)
–1728 [>>> -1728] to 1727 [>>> 1727] (system frequency: 50i)
Factory default setting: *0 [>>> 0]
–512 [>>> –512] to 511 [>>> 511]
Factory default setting: *0 [>>> 0]
Note
Valid for serial number 11001 or higher and firmware version
1.5 or higher.