Regency Ultimate U39E Series Owners & Installation Manual page 12

owner's information
Continuous Pilot/Intermittent Pilot (CPI/IPI) selection
Note: Power vent models do not have a Continuous
Pilot option.
With the system in "OFF" position press the Mode Key (fi g. 1) to index
to the CPI mode icon (fi g. 19 & 20).
Pressing the Up Arrow Key will activate the Continuous Pilot Ignition
mode (CPI). Pressing the Down Arrow Key will return to IPI. A single
"beep" will confi rm the reception of the command.
Figure 19
CPI/IPI SWITCH
This appliances comes equipped with a CPI/IPI switch. The function of
both the CPI/IPI switch are as follows:
Continuous pilot (CPI) - A pilot that when in operation, is intended to
remain continuously ignited until it is manually interrupted.
Intermittent pilot (IPI) - A pilot that is automatically ignited when an ap-
pliance is called on to operate and which remains continuously ignited
during each period of main burner operation. The pilot is automatically
extinguished when each main burner operating cycle is completed. The
mode of the fi replace is easily changed from an intermittent pilot ignition
system (IPI) to a continuous pilot ignition system (CPI) by using remote
control as noted above.
The benefi ts of having as CPI are as follows:
- Keeps venting primed for trouble free start-up under colder weather
conditions or inversions.
- Keeps the unit glass warm, which decreases the amount of condensa-
tion on start-up
-Provides owners with fl exibility to choose a traditional continuous pilot.
The primary benefi t of having the IPI function is a signifi cant savings on
fuel as the pilot will only run when there is a call for heat.
Thermostat Icon: If the thermostat icon is not present on the remote
transmitter, follow instructions noted below
1. Take one or all batteries out (removing one battery will work).
2. Press and hold down the Thermostat button on the remote.
3. Reinstall the 3rd battery while still holding thermostat button down.
4. If you see "Set" the thermostat option is now enabled. If you see "Clr"
the thermostat option is now disabled
5. Repeat the procedure if you did not see the "Set" or "Clr" to remove
or add the option back to the remote.
Enable all other functions if not present on the remote transmitter, follow
instructions noted below:
1. Remove one battery or all batteries (removing one battery will work).
2. Press and hold both the ON/OFF and the MODE button at the same time .
3. Reinstall the 3rd battery while still holding both buttons (keep holding
buttons once 3rd battery is installed, then release the mode button only.
4. The screen will show either "Clr" or "Set" with the 1st mode being
your option to disable or enable.
|
12
Regency U39E-11 ULTIMATE™ Freestanding Gas Stove
®
919-829
5. "Clr" will remove the mode by using the up or down arrow while still
6. Use the "Mode" button to move to the next function.
7. "Set" will add that mode by using the up or down arrow while still
Note: You should never program out the fan (if installed) or CPI/IPI
KEY LOCK
This function will lock the keys to avoid unsupervised operation.
To activate this function, press the MODE and UP Keys at the same
time (fi g. 21).
To de-activate this function, press the MODE and UP Keys at the
same time.
Figure 20
LOW BATTERY POWER DETECTION
Transmitter
The life span of the remote control batteries depends on various factors:
quality of the batteries used, the number of ignitions of the appliance,
the number of changes to the room thermostat set point, etc.
When the Transmitter batteries are low, a Battery Icon will appear on the
LCD display of the Transmitter (Fig. 22) before all battery power is lost.
When the batteries are replaced this Icon will disappear.
4
holding both buttons (icon will disappear once removed, or icon will
show up again once added).
holding both buttons (icon will disappear once removed, or icon
will show up again once added) Use the "Mode" button to move
to the next function.
mode on the remote.
Figure 21
Figure 22
09.29.17