Table of Contents
Advertisement
Quick Links
Operation and Maintenance Manual
SEM Model 0205 EMD E-Media Destroyer
POP-0086 – Rev 0 | Created 3-27-19 – ECN-00340
Serial Numbers 000100 and up
For sales, service, parts, and customer support, contact us:
SECURITY ENGINEERED MACHINERY
5 Walkup Drive • Westborough, MA 01581
info@semshred.com
1-508-366-1488 • Toll Free US 1-800-225-9293
www.semshred.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SEM 0205
Summary of Contents for SEM 0205
- Page 1 Operation and Maintenance Manual SEM Model 0205 EMD E-Media Destroyer POP-0086 – Rev 0 | Created 3-27-19 – ECN-00340 Serial Numbers 000100 and up For sales, service, parts, and customer support, contact us: SECURITY ENGINEERED MACHINERY 5 Walkup Drive • Westborough, MA 01581 info@semshred.com...
-
Page 2: Table Of Contents
SEM Model 0205 EMD E-Media Destroyer Table of Contents Table of Contents ..............................1 Disclaimers ................................2 Safety Procedures ..............................3 1. Introduction ............................... 4 2. Items and Packaging ............................4 2.1 Unpacking ..............................4 3. Operation ................................5 3.1 Unacceptable Media ........................... 5 3.2 Set Up………………………………………………………………………………………………………………………………………………….. -
Page 3: Disclaimers
SEM Model 0205 EMD E-Media Destroyer Disclaimers Every care has been taken by the staff of SEM in compilation of the data contained in all training and informational materials (“collateral”) and in verification of its accuracy when published; however, the content of this collateral is subject to change without notice due to factors outside the control of SEM and this collateral should therefore be used as a guide only. -
Page 4: Safety Procedures
SEM Model 0205 EMD E-Media Destroyer IMPORTANT SAFETY PROCEDURES Your new electronic media shredder incorporates powerful, heavy duty cutting mechanisms. Serious and permanent injury may result if proper precautions are not followed. 1. This equipment should never be operated by children or individuals that are untrained or incapable of understanding these safety precautions. -
Page 5: Introduction
2.1 Unpacking Upon receipt of your SEM 0205 EMD, be sure to inspect the unit for damage and note any such items on the Bill of Lading, and contact SEM customer service. Retain packaging for at least 90 days. -
Page 6: Operation
SEM Model 0205 EMD E-Media Destroyer 3.) Operation The SEM 0205 EMD Electronic Media Destroyer has been designed for secure destruction of solid state media, phones, tablets (disassembled/board only), flash drives, and more. Phones, PDAs and small tablets can be destroyed ONLY after removing the battery and LCD screens. -
Page 7: Set Up
SEM Model 0205 EMD E-Media Destroyer 3.2 Set Up Before using the unit, ensure that the waste bin and a bag have been installed in the unit. Attach the appropriate power cord to the receptacle at the rear of the unit. Attach the other end to a dedicated wall outlet. -
Page 8: Powering On
Upon powering up, the display screen will immediately illuminate. The initial SEM splash screen will appear for several seconds. It shows the unit name and model number. • When the SEM splash screen disappears, the main user screen will now be displayed. The unit is now ready for use. •... -
Page 9: Feeding Media
SEM Model 0205 EMD E-Media Destroyer 3.4 Feeding Media • Media can be fed by sliding it through the feed flap or by holding the feed flap open with your hand, letting the media slide down the Ramp and then closing the feed flap. -
Page 10: Display Messages
SEM Model 0205 EMD E-Media Destroyer 3.5 Display Messages The shred cycle will run for 10 seconds. Once the shred cycle starts, the WAIT! DO NOT FEED message will be displayed. NEVER feed media while this message is displayed, as the unit is busy shredding or not ready to accept media. -
Page 11: Jams
SEM Model 0205 EMD E-Media Destroyer Anytime the waste bin door or unjam door is opened, the DOOR icon will appear indicating that either of these doors is opened. The unit is designed with a braking feature that will bring the cutting head to a stop in less than one second in the event that the waste bin door or unjam door is opened. - Page 12 Close the unjam door and replace the screw. This screw MUST remain in place while the unit is operational. It is a safety guard. CAUTION: partially shredded material may be sharp. SEM recommends cut resistant gloves. Cutting Head Unjam Door Screw 508.366.1488 | www.semshred.com...
-
Page 13: Low Power/Standby Mode
If the unit is not used and the LCD interface display is untouched for several minutes, the unit will go into low power mode and the display will revert to the SEM splash screen with a dimmed screen. If the unit is further untouched for several more minutes, the screen will turn fully black. -
Page 14: Maintenance
If this occurs, the HOT indicator will appear and the user must wait for it to automatically reset. Service Needed Symbol If the unit encounters many errors or an unsafe condition is detected, the SERVICE NEEDED screen and symbol is displayed. If this occurs, please contact SEM customer support. 508.366.1488 | www.semshred.com... -
Page 15: Contact And Accessories
Customer Service Tel: 508.366.1488 Fax: 508-366-6814 service@semshred.com IMPORTANT Two to three preventive maintenance calls per year are recommended Only authorized, SEM trained service personnel should service the shredder. Accessories Part Number Description 640ASB0202 Case of 50 Anti-Static Waste Collection BAGS... - Page 16 SEM Model 0205 EMD E-Media Destroyer For sales, service, parts, and customer support, contact us: SECURITY ENGINEERED MACHINERY 5 Walkup Drive • Westborough, MA 01581 info@semshred.com 1-508-366-1488 • Toll Free US 1-800-225-9293 www.semshred.com Follow us on social media: Facebook: https://www.facebook.com/semshred Twitter: https://twitter.com/semsecure...
Need help?
Do you have a question about the 0205 and is the answer not in the manual?
Questions and answers