Related Manuals for ADS-tec VMT9000 Series
Summary of Contents for ADS-tec VMT9000 Series
- Page 1 Translation of the original instruction manual version 1.2 Instruction manual Terminals VMT9000 series Updated 2019-05-07...
- Page 2 These instructions can be downloaded from: www.ads-tec.de in the download area. Publisher ads-tec Industrial IT GmbH Heinrich-Hertz-Straße 1 72622 Nürtingen Phone: +49 7022 2522-0 Internet: www.ads-tec.de E-mail: mailbox@ads-tec.de © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...
-
Page 3: Table Of Contents
Interface overview 5.4.1 Power supply 5.4.2 Ignition function 5.4.3 Earthing concept 5.4.4 Autostart 5.4.5 Serial interface COM1 (RS232) 5.4.6 Optional: serial interface COM2 (RS232) Closing the service slot © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... - Page 4 10 Dimensional drawings ......................37 10.1 VMT9010 10.2 VMT9012 10.3 VMT9112 10.4 VMT9015 11 Technical data ........................41 12 Service & support ......................... 42 12.1 ADS-TEC support 12.2 Company address © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...
-
Page 5: General Information About Documentation
Information on how to avoid the hazard is indicated by an arrow (). DANGER Type and source of the hazard! Possible consequences if the hazard is disregarded Measures for avoiding the hazard © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 6: Explanation Of Signal Words
Indicates terms and/or conditions that strictly need to be observed to ensure optimised and/or zero-defect operation. Tips and suggestions for the efficient use of the device and software optimisation are also provided. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 7: Relevant Device Documentation
ADS-TEC. All other used third-party trademarks are hereby acknowledged. In the case of trademark infringement, ADS-TEC reserves the right to exercise all rights. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 8: Copyright
Any modified use or exploitation of the provided content, particularly duplication, modification or publishing in whatever form is permitted only with the prior consent of ADS-TEC. In the case of copyright infringement, ADS-TEC reserves the right to exercise all rights. -
Page 9: General Device Information
VMT9000 series − Instruction manual v1.2 2 General device information 2.1 Manufacturer and contact details The manufacturer of the device is ads-tec Industrial IT GmbH. The company is referred to in the following as ADS-TEC. ads-tec Industrial IT GmbH Heinrich-Hertz-Str.1 72622 Nürtingen... -
Page 10: Improper Use
In the case of improper use, ADS-TEC shall not accept responsibility or liability for injury or damage that is directly or indirectly attributable to the handling of the device. -
Page 11: Environmental Conditions
The device can be operated under the environmental conditions specified in the technical data. Failure to observe any one of these conditions will invalidate the warranty of the device. ADS-TEC cannot be held liable for any damages arising from improper use and handling. -
Page 12: Conformity
It is therefore necessary to employ BUS and LAN cables with shielded connectors and these must be installed as per the instructions contained in the instruction manual. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 13: Warranty / Repairs
2.7 Limitation of liability ADS-TEC shall not be liable for personal injury, property damage or damage caused to the device as well as consequential damage that is/was the result of non-compliance with this instruction manual, improper use of the device, repairs and other actions on the device by unqualified electricians and electricians not certified by ADS-TEC, or that is/was the result of using unapproved replacement parts. -
Page 14: Treatment And Disposal Of Lithium Batteries
The battery type to be used is: • Lithium battery CR2032 • ADS-TEC part number: DZ-SONS-09946-1/A The used lithium battery should be disposed of in accordance with local legal regulations. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 15: Scope Of Delivery
Check that the contents of the package are complete and match your order: − 1 x device − 1 x 4-pin plug for power supply in service slot − Accessories according to order/delivery note © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 16: Mechanical Installation
If the device is exposed to sunlight or any other light or heat source, it can overheat and suffer damage. • Do not expose the device to direct radiation by sunlight or any other light or heat source! © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 17: Mounting The Device
The images show typical screw lengths when using the RAM mount and/or optional scanner holder. l = 8 mm l = 10 mm l = 14 mm © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 18: Other Options
Sequence (each from the inside to the outside): Allen screw torque: 40 Nm (recommended) • Further information and dimensional drawings can be found on our website in the section "Accessories" for the respective device. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 19: Electrical Connections
The electronics can be damaged if connectors are connected or disconnected while power is still being applied. • Make sure that no power is being applied when connecting and disconnecting connectors. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 20: Opening The Service Slot
VMT9000 series − Instruction manual v1.2 5.2 Opening the service slot 1. Loosen screws (Tx20) 2. Lift cover at left 3. Pull cover off to left © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 21: Compliance With The Ip Protection Class
After connecting the cable lines: close service slot as described in chapter 5.5. Example of cable routing: Recommendation for use: On the inner side, attach cable ties for strain relief. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 22: Interface Overview
Slot for Nano SIM card ⇨ see section 7.5 and MicroSD card ⇨ see section 7.1 *) The USB interfaces can be disabled individually in the Configuration Center. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 23: Power Supply
This function can be activated and configured in the Configuration Center. Recommendation for use: Generally, the autostart and ignition functions should not be used together because these functions partly overlap. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 24: Earthing Concept
PE earthing lug in the service slot for earthing the device housing • Recommendation If possible, FE and PE should be connected via separate cables to the vehicle ground or respectively to the main earthing. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 25: Autostart
The autostart function is activated using the switch (shown) in the service slot. Recommendation for use: Generally, the autostart and ignition functions should not be used together because these functions partly overlap. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 26: Serial Interface Com1 (Rs232)
Please note: In addition, the corresponding software switch in the Configuration Center must be set to ON, see module Serial port data forwarding. 5.4.6 Optional: serial interface COM2 (RS232) Interface Address COM2 2F8h © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 27: Closing The Service Slot
5.5 Closing the service slot 1. Insert the cover on the right side into the groove 2. Press down the cover on the left side 3. Tighten screws with 0.5 Nm © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 28: Commissioning
Hazard due to condensation Damage to electronic components caused by condensation resulting from temperature fluctuations. • Switch on the device only after it has acclimated to the ambient temperature! © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 29: User Interfaces
Optional: RFID reader (not visible) ON/OFF pushbutton *) The USB interfaces can be disabled individually in the Configuration Center. **) Functionality can be configured in the Configuration Center. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 30: Functions Of The Front Keys Ex Factory
Shift key (SHIFT) for the second keyboard level. This key must be pressed simultaneously with the desired function key. Reduce brightness Increase brightness Reduce volume Increase volume 6.2.3 Rear side Speakers are located at the shown positions. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 31: Switching On And Configuring Device
In its delivery state, a soft keyboard can be displayed by pressing the function key S1. The Configuration Center from ADS-TEC can be used to make a number of settings, e.g.: − Assignment of functions to the front keys −... -
Page 32: Features
If you pull the drawer with a SIM card inserted while the computer is running, the device switches off immediately. Unsaved data will be lost! • Shut down the computer before pulling out the drawer with the SIM card inserted. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 33: Rfid Reader (Optional)
In the Configuration Center, it is possible to set whether the internal or an external WLAN antenna is to be used. 7.4 Bluetooth (optional) Devices with WLAN also have Bluetooth. This function uses the resources provided by the operating system. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 34: Mobile Communications (Optional)
If you pull the drawer with a SIM card inserted while the computer is running, the device switches off immediately. Unsaved data will be lost! • Shut down the computer before pulling out the drawer with the SIM card inserted. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 35: Gps (Optional)
A GPS antenna can be connected to the connection socket (SMA female) in the service slot. 7.7 CAN FD (optional) This function uses the resources provided by the operating system. Other connectors can be provided here at the request of the customer. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 36: Software / Driver Installation
After the software installation has been changed, the write protection must be set again and the device restarted. 9 Cleaning Clean the device using some glass cleaner on a soft cloth. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 37: Dimensional Drawings
VMT9000 series − Instruction manual v1.2 10 Dimensional drawings 10.1 VMT9010 © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 38: Vmt9012
VMT9000 series − Instruction manual v1.2 10.2 VMT9012 © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 39: Vmt9112
VMT9000 series − Instruction manual v1.2 10.3 VMT9112 © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 40: Vmt9015
VMT9000 series − Instruction manual v1.2 10.4 VMT9015 © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 41: Technical Data
Antenna: external antenna with WLAN magnetic base Dimensions 277 x 249 x 50 mm 312 x 277 x 50 mm 331 x 256 x 50 mm 380 x 326 x 50 mm © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany... -
Page 42: Service & Support
ADS-TEC does not provide support services for any device that was not purchased directly from ADS- TEC. In this case, maintenance and support is provided by the partner company.