Related Manuals for ADS-tec HDT8012
Summary of Contents for ADS-tec HDT8012
- Page 1 Version Translation of the original manual Instruction manual Terminal HDT8012 Updated 2018-02-12...
-
Page 2: Table Of Contents
Interfaces in the service slot 4.2 Power supply 4.3 Earthing (PE / FE) 4.4 Ignition function (IGN) 4.5 Autostart function (switch S1) 4.6 Serial interface X3 COM 4.7 LAN network connection 4.8 USB connections © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 3: Hdt8012
8 Drives 9 Software & driver installation 10 Maintenance 10.1 Information on maintenance 10.2 Information on storing the batteries 11 Technical details 12 Service & support 12.1 ADS-TEC support 12.2 Company address © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 4: Notes
Furthermore, it is strictly forbidden to make any unauthorised alterations or technical modifications to the device. 1.3 Manufacturer The manufacturer of the product is ads-tec GmbH. The company is referred to in the following as ADS- TEC. 1.4 Relevant device documentation... -
Page 5: Safety Instructions
The symbol "Recommendation for use" indicates terms and/or conditions that strictly need to be observed to ensure optimised and/or zero-defect operation. Tips and suggestions for the efficient use of the device and software optimisation are also provided. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 6: Symbols
StoraXe® and Big-LinX® are registered trademarks of ADS-TEC. All other used third-party trademarks are hereby acknowledged. In the case of trademark infringement, ADS-TEC reserves the right to exercise all rights. 2.7 Copyright This instruction manual is protected by copyright. For the authorised user, simple usage rights are granted within the scope of the intent of the contract. -
Page 7: Environmental Conditions
The device can be put into operation and used under the following conditions. Failure to observe any one of these conditions will invalidate the warranty of the device. ADS-TEC cannot be held liable for any damages arising from improper use and handling. -
Page 8: Conformity
It is therefore necessary to employ BUS and LAN cables with shielded connectors and these must be installed as per the instructions contained in the instruction manual. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 9: Operating And Safety Instructions
Hazard due to damage to device Damage caused by connected peripherals or data loss All cable lines (power supply, interface cables) should only be connected while the device is switched off and de-energised. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 10: Operating Location
In the case of improper use, ADS-TEC shall not accept responsibility or liability for injury or damage that is directly or indirectly attributable to the handling of the device. -
Page 11: Treatment And Disposal Of Lithium Batteries
The battery type to be used is: Lithium battery 1/2AA 3V FDK Corp. CR14250SE ADS-TEC part number: DZ-SONS-04100-0 The used lithium battery should be disposed of in accordance with local legal regulations. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 12: Safety Instructions
Recommendation for use: Always adhere to the safety measures applicable when handling components at risk of being damaged by electrostatic discharges. The provisions of DIN EN 61340-5-1 / DIN EN 61340-5-2 apply © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 13: Product Description
HDT8012 4 Product description 4.1 Features and interfaces 4.1.1 Front view Description Touch-sensitive screen (touch-screen) → see section 7.1 System LED → see section 7.2 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 14: Rear View
4.1.2 Rear view Description Speakers → see section 7.4 Service slot for interfaces → see section 4.1.3 Interface VESA 75 → see section 5.2 Optional: ON/OFF push-button → see section 7.3 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 15: Interfaces In The Service Slot
COM (RS232) → see section 4.6 X3:COM X4:LAN1 LAN connections (RJ45) → see section 4.7 X5:LAN2 X6:USB1 USB connections (USB 2.0) → see section 4.8 X7:USB2 X8:USB3 Cable entry grommets Protective earth, → see section 4.3 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 16: Power Supply
Do not operate the device on vehicles that can exceed the permissible system voltage. Note on use in accordance with UL-Certification (Underwriter Laboratories): The device is designed for an LPS supply (Limited Power Source/Class2). © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 17: Earthing (Pe / Fe)
The computer can also be automatically shut down in a time-controlled manner if voltage is no longer present at the release contact. Prefabricated supply cables are available from ADS-TEC for using this function. 4.5 Autostart function (switch S1) The autostart function allows the automatic start-up of the device upon application of the supply voltage. -
Page 18: Serial Interface X3 Com
(max. 1 A) Note: This interface is not electrically isolated. 4.7 LAN network connection Features: ̶ 10/100/1000Mbit/s, RJ45 ̶ 2 x Intel I211 GbE network controllers ̶ PXE-boot is supported (Preboot Execution Environment) © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 19: Usb Connections
The USB interfaces have a current limit of 1 A per USB interface. Pos : 30 /D atentec hni k/Schnitts tell en/PS2/Kombi Buc hs e für VMT 60xx @ 2\mod_1268840073235_6.doc @ 7482 @ © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 20: Installation
HDT8012 5 Installation 5.1 External device dimensions © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 21: Installation Via The Vesa-75 Interface
The device can be damaged if the permitted tightening torque is not observed when the VESA bracket is screwed on. Tighten the screws to max. 5 Nm. If necessary: also use a suitable threadlocker, e.g., low-strength liquid adhesive. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 22: Other Mounting Options (Optional)
HDT8012 5.3 Other mounting options (optional) Description ® Bracket for Rittal housing connector top VESA 75 Standard bracket Table/vehicle bracket Mounting bracket left/right ® Bracket for Rittal housing connector bottom © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 23: Commissioning
All installation and service work performed on the device must be performed only under safe, secure and de-energised conditions. Recommendation for use: The shielding of a data cable must always be connected with the connector housing (EMC). © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 24: Order Of Steps During Commissioning
The device should be operated by trained and instructed personnel only. The manufacturer must be contacted if damage is found. 6.5 Decommissioning The device can be shut down using the ON/OFF pushbutton, the ignition function and using the software. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 25: Operation
The system LED (1) indicates the operational readiness of the device. 7.3 ON/OFF pushbutton (optional) Located on the rear side of the device is a button. The functionality is dependent on the configuration (e.g., ignition signal, operating system, autostart switch). © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 26: Speakers
HDT8012 7.4 Speakers The devices have two internal speakers on the rear side. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 27: Drives
Data loss might result in the event of non-compliance! © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 28: Software & Driver Installation
For this purpose, the appropriate BootROM extension must first be activated in BIOS and then selected in the boot menu. The further course of action is dependent on the network environment and the operating system that is to be installed. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 29: Maintenance
Secure connection and According to VDE0113 connections correct operation 10.2 Information on storing the batteries When storing batteries, always observe the relevant regulations: no direct sunlight, dry room, no frost, etc. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 30: Technical Details
307 x 245 x 61 mm Weight Approx. 3.0 kg Vibration and shock EN 60721-3-5:1998-06 Environmental conditions for devices for terrestrial vehicles: Class 5M3 (for mass storage type SSD) resistance Humidity 10 to 85% non-condensing © ads-tec GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 31: Service & Support
ADS-TEC does not provide support services for any device that was not purchased directly from ADS- TEC. In this case, maintenance and support is provided by the partner company.