Table of Contents
Advertisement
Quick Links
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com
Roll Stand Kit – 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle,
The purpose of this guide is to:
1. Describe assembly of the Roll Stand (pages 2 - 4).
2. Describe tilt and swivel adjustments, and cable management (page 5).
Parts Reference
The following parts and hardware are included with this installation kit (hardware not shown):
Item #
Description
1
Roll Stand Post'
2
Roll Stand Base with 10 lbs/4.5kg Counterweight
3
5/16-18 x 1'' Hex Head Cap Screw (HHCS)
4
5/16 Flat Washer
5
5/16 Split Lock Washer
6
Utility Basket (includes mounting hardware)
7
Handle (includes mounting hardware)
8
Swivel/Tilt Mounting Plate Assembly
9
Cable Clip
10
5/32'' Hex Wrench
11
2.5 mm Hex Wrench
Tools Required
Phillips screwdriver (not provided)
5/32'' [4 mm] hex wrench (provided)
2.5 mm hex wrench (provided)
1/2'' [13mm] wrench (not provided)
Installation Guide
Utility Basket and 10lbs/4.5kg Counterweight
Qty
1
1
1
1
1
1
1
1
1
2
1
1
DU-RS-0006-64 Rev B 3/28/14 GCX Corp Page 1 of 5
9
8
7
6
2
Advertisement
Table of Contents
Related Manuals for GCX RS-0006-64
Summary of Contents for GCX RS-0006-64
- Page 1 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Roll Stand Kit – 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle, Utility Basket and 10lbs/4.5kg Counterweight The purpose of this guide is to: 1. Describe assembly of the Roll Stand (pages 2 - 4).
- Page 2 Roll Stand Post Roll Stand Base Locking Casters (5) Push pedal down to lock. Lift pedal to unlock. 5/16 Flat Washer (1) 5/16 Split Lock Washer (1) 5/16-18 x 1'' HHCS (1) DU-RS-0006-64 Rev B 3/28/14 GCX Corp Page 2 of 5...
- Page 3 1. Insert Mounting Plate Assembly in top of Post (below left). Press downward while twisting until the Assembly snaps into place. Swivel the Mounting Plate until the spring-loaded plunger is toward the front of the Roll Stand. Mounting Plate Assembly Plunger toward Front DU-RS-0006-64 Rev B 3/28/14 GCX Corp Page 3 of 5...
- Page 4 Handle does not rotate around Post. Installation Note: Handle position shown is typical but Handle may be attached at any desired location on the Post. #10-32 x 9/16'' PHMS (2) DU-RS-0006-64 Rev B 3/28/14 GCX Corp Page 4 of 5...
- Page 5 Dry all mounting assemblies thoroughly after cleaning. CAUTION: GCX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling infection. Consult your hospital’s infection control officer or epidemiologist. To clean or sterilize mounted instruments or accessory equipment, refer to the specific instructions delivered with those products.
Need help?
Do you have a question about the RS-0006-64 and is the answer not in the manual?
Questions and answers