Sony 300PF Operating Instructions Manual page 85

Advanced menu page 2
P A G E 2 ( N E X Tm$ P R E V m4)
G A I N
m H I G H : 1 8 d B
M I D : 9 d B
L O W : O d B
D L : O N
E X I T M E N U ( Y E SmPUSH)
Item
GAIN
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
HIGH
Sets the H position.
MID
Sets the M position.
LOW
Sets the L position.
DL
Sets DynaLatitude function
ON/OFF. This setting is
valid only when the
OUTPUT/DL/DCC+ switch
has been set to DL.
Settings
3 dB, 6 dB, 9 dB, 12 dB, 18
dB (normal value), 18 dB +
DPR, 24 dB, 24 dB + DPR,
HYPER GAIN
0 dB, 3 dB, 6 dB, 9 dB
(normal value), 12 dB, 18
dB, 18 dB + DPR, 24 dB, 24
dB + DPR
–3 dB, 0 dB (normal
value), 3 dB, 6 dB, 9 dB, 12
dB, 18 dB, 18 dB + DPR, 24
dB
ON (normal value), OFF
When set to ON, the amount
of DynaLatitude effects is
set in basic menu page 2
(see page 79).
Advanced menu page 3
P A G E 3 ( N E X Tm$ P R E V m4)
mA W B M E M
P R E . W H T : 3 2 0 0
T O N E
B A R S
R E M O T E 1
R E M O T E 2
B A U D R A T E : 3 8 4 0 0
E X I T M E N U ( Y E SmPUSH)
a) For DSR-300P: EBU75
Item
AWB MEM
Selects whether or not to
make the FILTER knob
settings (1 to 4) correspond
to separate white balance
adjustment values stored in
memory.
PRE. WHT
Selects the color
temperature preset for the
white balance adjustment.
TONE
Selects whether or not to
output a 1-kHz audio signal
with the color bars when the
OUTPUT/DL/DCC+ has
been set to BARS.
BARS
Selects normal width or
narrower width for color
bars.
REMOTE1
Sets a function for position 1
of the RM-LG1 connected to
the REMOTE connector 1.
REMOTE2
Sets a function for position 2
of the RM-LG1 connected to
the REMOTE connector 1.
BAUD RATE
Sets a baud rate for a
computer connected to the
REMOTE connector 1 (to be
supported in future version).
Chapter 4 Viewfinder Screen Indications and Menus
: 2
: O N
a )
: S M P T E
: R E C
: M A R K
Settings
2 (normal value): No
correspondence with FILTER
knob settings. Only two
adjustment values (A and B)
are stored in memory.
2 4FL: Correspondence
with FILTER knob settings.
Each of the four knob
settings can be used to set A
and B adjustment values, for
a total of eight settings.
3200 (normal value):
3200 K
3000: 3000 K
ON (normal value): Output
audio signal.
OFF: Do not output audio
signal.
SMPTE (normal value for
DSR-300): Normal width
EBU75 (normal value for
DSR-300P): EBU 75%
EBU100 (for DSR-300P):
EBU 100%
SPLIT (for DSR-300P): Not
for normal operation
SNG: Narrower than normal
(used for satellite
communications, etc.)
REC (normal value):
Specifies recording start/stop
MARK: Specifies a Mark IN/
OUT point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
REC: Specifies recording
start/stop.
MARK (normal value):
Specifies a Mark IN/OUT
point.
CUE: Specifies a Cue point
NG: Specifies NG/OK.
9600, 38400 (normal value)
85