Parameters Concerning Digital Inputs And Output - Carel FCM series Manual

8.5

Parameters concerning digital inputs and output

C29: Multifunction digital input ID1
C29 indicates the function of the digital input ID1.
Access:
Keypad:
Remote control:
Modes:
Operating range:
Ü
C29=0
Ü
C29=1
Ü
C29=2
Ü
C29=3
Ü
C29=4
Ü
C29=5
Default:
Note: if the function associated with the input ID1 is the same as that associated with the input ID2, ID1 has priority
C30: Multifunction digital input ID2
C30 indicates the function of the digital input ID2.
Access
Keypad:
Remote control:
Operating range:
Ü
C30=0
Ü
C30=1
Ü
C30=2
Ü
C30=2
Ü
C30=3
Ü
C30=4
Ü
C30=5
Default:
Note: if the function associated with the input ID1 is the same as that associated with the input ID2, ID1 has priority
C31: Multifunction (relay) digital output
C31 indicates the function of the relay digital output (if not differently used according to the selected operating mode).
Access:
Keypad:
Remote control:
Modes:
Operating range:
Ü
C31=0
Ü
C31=1
Ü
C31=2
Ü
C31=3
Ü
C31=4
Ü
C31=5
Ü
C31=6
Ü
C31=7
Ü
C31=8
Default:
FCM electronic regulator
Ü
if C50=1, 3 or 4 +
Ü
if C50=0 or 2
Ü
if C50=4
only when C00=0, 1, 2, 3
from 0 to 5
input not used
external alarm and automatic reset (alarm with open input)
external alarm and manual reset (alarm with open input)
delayed external alarm and manual reset (alarm with open input; time-delay set by P28)
On/Off regulation (off when open input): when in the Off status, the analogue output will be immediately
disenergized (0 V)
÷
energization of the 0 10 V analogue output to 100%: when the input is closed, the analogue output is forced
to 0 V.
Ü
C29 = 0 input not used.
Ü
if C50=1, 3 or 4 +
Ü
if C50=4 press "ENABLE" and
from 0 to 5
input not used
external alarm and automatic reset (alarm with open input)
external alarm and manual reset (alarm with open input)
external alarm and manual reset (alarm with open input)
delayed external alarm and manual reset (alarm with open input): time-delay set by P28
On/Off regulation (off when open input): when in the Off status, the analogue output will be immediately
disenergized (0 V)
÷
energization of the 0 10 V analogue output to 100%: when the input is closed, the analogue output is forced
to 0 V.
Ü
C30 = 0 input not used
Ü
if C50=1, 3 or 4 +
Ü
if C50=4 press "ENABLE" and
not available when C00=8
from 0 to 8
output not used (disenergized relay)
disenergized relay in the event of generic alarm
energized relay in the event of generic alarm
disenergized relay in the event of active analogue output
energized relay in the event of active analogue output
disenergized relay when the analogue output has its max. value (hysteresis 0.5 V)
energized relay when the analogue output has its max. value (hysteresis 0.5 V)
disenergized relay when the analogue output reaches its max. value; energized relay when the
analogue output reaches its min. value (On/Off regulation)
energized relay when the analogue output reaches its max. value; disenergized relay when the
analogue output reaches its min. value (On/Off regulation).
Ü
C31 = 0 output not used.
for 5" and password 77;
the parameter can only be displayed..
press "ENABLE" and and
for 5" and password 77; if C50=0 or 2
and ;
for 5" and password 77; if C50=0 or 2
and ;
21
;
Ü
the param. can only be displayed.
Ü
the param. can only be displayed..
Cod. +302235300 - Rel. 2.0 del 30/11/98