Related Manuals for Baicells BRU35 Series
Summary of Contents for Baicells BRU35 Series
- Page 1 Nova-243 Outdoor LTE TDD Base Station Installation Guide All rights reserved © Baicells Technologies Co., Ltd.
- Page 2 This document suit for the models of BRU35xx series base station. Copyright Notice Baicells copyrights this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of Baicells. Disclaimer This specification is preliminary and is subject to change at any time without notice.
- Page 3 16 Jan, 2018 Optimize descriptions and fix some bugs. 4 Apr, 2018 Fix bugs. Contact Us Baicells Technologies Co., Ltd. Address: 3F, Bldg A, No.1 Kai Tuo Rd., Haidian Dist., Beijing, PR China, 100085 E-mail: support_cn@baicells.com/support_na@baicells.com Tel: 400-612-0167 Fax: +86-10-62607100...
-
Page 4: Table Of Contents
Nova-243 Outdoor LTE TDD Base Station Installation Guide Table of Contents Product Overview ......................1 Introduction ......................1 Features ......................... 1 Appearance ......................2 Technical Specification ................... 3 1.4.1 Hardware Specification ................... 3 1.4.2 Software Specification ..................4 1.4.3 Environment Specification ................5 Installation Preparation .................... - Page 5 Nova-243 Outdoor LTE TDD Base Station Installation Guide 3.6.3 Connect RF Cable ..................14 3.6.4 Connect Ethernet Cable................. 14 3.6.5 Connect Power Connector ................14 3.6.6 Connect Ground Cable .................. 16 Install Antenna Feeder System................17 3.7.1 Install Omnidirectional Antennas..............17 3.7.2 Install Directional Antennas ................
- Page 6 Nova-243 Outdoor LTE TDD Base Station Installation Guide List of Figures Figure 1-1 Nova-243 Appearance ................2 Figure 1-2 Nova-243 Interfaces and Indicators ............2 Figure 3-1 Installation Procedure of Nova-243 ............9 Figure 3-2 Install the GPS Antenna ................10 Figure 3-3 Pre-assembled bracket ................
-
Page 7: Product Overview
Nova-243 Outdoor LTE TDD Base Station Installation Guide 1. Product Overview Introduction Baicells Nova-243 is high performance outdoor micro base station based on LTE TDD technology, which is developed by Baicells. The Nova-243 supports wired backhaul connections to backbone networks, and provides LTE access to user terminals, implemented voice and data service transmissions. -
Page 8: Appearance
Nova-243 Outdoor LTE TDD Base Station Installation Guide Appearance The Nova-243 base station appearance is shown in Figure 1-1. Figure 1-1 Nova-243 Appearance The Nova-243 interfaces and indicators are shown in Figure 1-2. Figure 1-2 Nova-243 Interfaces and Indicators... -
Page 9: Technical Specification
Nova-243 Outdoor LTE TDD Base Station Installation Guide The Nova-243 interfaces are described in Table 1-1. Table 1-1 Nova-243 Interface Description Interface Name Description RJ-45 electronic interface, support 10M/100M/1000M ETH0 self-adaptation, external transmission network. ETH1 RJ-45 electric interface, used for debugging. External Sniffer, Type N interface ANT0 External antenna 1,Type N interface... -
Page 10: Software Specification
Nova-243 Outdoor LTE TDD Base Station Installation Guide Item Description BRU3510: 2496MHz~2690MHz / 2570MHz~2620MHz BRU3511: 3400MHz~3600MHz BRU3516: 2575MHz~2640MHz BRU3524: 2300MHz~2400MHz BRU3527: 3439.5MHz~3539.5MHz BRU3528: 2570MHz~2620MHz Channel Bandwidth* 5/10/15/20 MHz MAX Output Power 40dBm/Ant -101 dBm @band42/48 Receive Sensitivity -102 dBm @band38/40/41 Synchronization GPS, 1588 V2 Backhaul... -
Page 11: Environment Specification
Nova-243 Outdoor LTE TDD Base Station Installation Guide Item Description SIPTO (Selected IP Traffic Offload) Automatic setup ANR (Automatic Neighbor Relation) PCI confliction detection Spectrum Scanning Supported UL Interference Supported Detection RAN Sharing Supported Network Management TR069 Interface ≥ 150000 hours MTBF ≤... -
Page 12: Installation Preparation
Nova-243 Outdoor LTE TDD Base Station Installation Guide 2. Installation Preparation Supporting Materials Prepare the following support materials accordingly, as given in Table 2-1. Table 2-1 Support Materials Item Description Power cable < AWG16 e.g. AWG14 Shorter than 100m Power plug The power plug connecting to the electricity supply. -
Page 13: Installation Environment
Nova-243 Outdoor LTE TDD Base Station Installation Guide Installation Environment 2.3.1 Locational Requirements Environments with high-temperatures, harmful gases, unstable voltages, volatile vibrations, loud noises, flames, explosives, and electromagnetic interference (large radar stations, transmitting stations, transformer substations) are not suitable for the operation of Nova-243, and thus should be avoided. -
Page 14: Against Lightening And Grounding Protection
Nova-243 Outdoor LTE TDD Base Station Installation Guide training, and having the corresponding qualifications. Against Lightening and Grounding Protection CAUTION It is unlikely to happen but since the LTE base station is very sophisticated equipment so we would recommend you to test it on the ground to make sure everything is functioning before install on the tower. -
Page 15: Install The Base Station
Nova-243 Outdoor LTE TDD Base Station Installation Guide 3. Install the Base Station Unpacking Before opening the box, make sure the package is in good condition, undamaged and not wet. During the unpacking, avoid potential damaging impacts from hits or excessive force. -
Page 16: Install On Pole
Nova-243 Outdoor LTE TDD Base Station Installation Guide The GPS cable should be as shorter as possible to reduce the influence to signal strength. The GPS has been assembled before packing, the only installation step is to fix the GPS mounting bracket on the base station using the M4 x 14 screws, as shown in Figure 3-2. - Page 17 Nova-243 Outdoor LTE TDD Base Station Installation Guide Make sure the base station’s installation height, fit the thread rod of the assembled bracket to the pole, and then pass the two omegas through the threaded rods, and fasten the four flat gaskets, four spring gaskets, and four nuts. Mount the base station vertically on the bracket and tighten M6 screw on the top of bracket using cross screwdriver to complete the installation.
-
Page 18: Install On Wall
Nova-243 Outdoor LTE TDD Base Station Installation Guide Install on Wall The wall must bear four times of the base station’s weight. Take apart the assembled bracket. Install three mounting hooks on the base station with M6 x 16 screws. Fit the base station with hooks on the wall, and mark the drilling locations. -
Page 19: Connect Cable
Nova-243 Outdoor LTE TDD Base Station Installation Guide Drill three 12mm diameter holes in the wall on the marked locations, and insert the expansion pipes. Fix base station to the wall with M8 x 80 expansion bolts. Connect Cable 3.6.1 Requirement for Cable Laying General requirements: Bending radius requirement of feeder cable: 7/8”... -
Page 20: Connect Gps Antenna
Nova-243 Outdoor LTE TDD Base Station Installation Guide 3.6.2 Connect GPS Antenna Insert GPS jumper into cold shrink tube. Connect one end of the GPS jumper to the GPS antenna. Push the cold shrink tube to the top joint and pull out the strip. Connect the other end of the GPS jumper to GPS interface of the base station, which also need weatherproof protection. - Page 21 Nova-243 Outdoor LTE TDD Base Station Installation Guide corresponding terminals separately, and tighten screws. Assemble power terminal. The power terminal will be installed on the end of output direction. Refer to the following figure to connect live wire and neutral wire. Connect the power cable to PWR interface in the wiring cavity.
-
Page 22: Connect Ground Cable
Nova-243 Outdoor LTE TDD Base Station Installation Guide After the cable connection is complete in the wiring cavity, tighten the screws on the cover to close the wiring cavity using M4 cross screwdriver. 3.6.6 Connect Ground Cable Make the grounding cable according the actual situation of the installation site. The Nova-243 provides two grounding screws, which is located on the bottom of the base station, as shown in Figure 3-4. -
Page 23: Install Antenna Feeder System
Nova-243 Outdoor LTE TDD Base Station Installation Guide Install Antenna Feeder System There are two kinds of outdoor antennas, omnidirectional outdoor antennas and directional outdoor antennas, whose installation will be introduced in the following, respectively. 3.7.1 Install Omnidirectional Antennas One should pay attention to the followings while installing the omnidirectional outdoor antenna: ... -
Page 24: Install Directional Antennas
Nova-243 Outdoor LTE TDD Base Station Installation Guide Figure 3-6 Omnidirectional Antenna Installation (2) 3.7.2 Install Directional Antennas First, assemble the antennas, as shown in Figure 3-7. Figure 3-7 Assembling Procedure of Directional Antennas To install it on the iron tower, use a pulley to transport the antenna assembled to the platform on the iron tower, as shown in Figure 3-8. -
Page 25: Figure 3-8 Transportation The Antennas In The Height
Nova-243 Outdoor LTE TDD Base Station Installation Guide Figure 3-8 Transportation the Antennas in the Height Fix the pole vertically to the ground or concrete pillars on the rooftop using expansion screws, and fasten it with steel wires. Then, mount the directional outdoor antenna onto the pole using the installation rack, as shown in Figure 3-9. -
Page 26: Power On
Nova-243 Outdoor LTE TDD Base Station Installation Guide 4. Power On Power on the Nova-243, and the indicators will light up, as shown in Figure 4-1. Figure 4-1 LED Indicators The explanation of the indicator signal is given in Table 4-1. Table 4-1 Nova-243 Indicator Description Identity Color... -
Page 27: Appendix A Additional Information
Following are the list of antennas certified for use. Customers can choose according to use environment of different antenna. The antenna list is given as follows. Antenna Antenna Type Manufacturer Model Number Gain(dBi) External Planar Baicells Technologies ANT-2G17-R-65- Antenna Dual Pole Co., Ltd EDT0 External Planar Baicells Technologies ANT-2G15-R-65- Antenna Dual Pole Co., Ltd... - Page 28 Nova-243 Outdoor LTE TDD Base Station Installation Guide Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 29 Nova-243 Outdoor LTE TDD Base Station Installation Guide mê me si le brouillage est susceptible d'en compromettre le fonctionnement. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 4.5m from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance.