1. Manuals
  2. Brands
  3. Launch Manuals
  4. Diagnostic Equipment
  5. ROXIE W
  6. User manual

Launch ROXIE W User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
LAUNCH
Copyright Information
Copyright © 2018 by LAUNCH TECH. CO., LTD. All rights reserved. No part of
this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying and recording
or otherwise, without the prior written permission of LAUNCH. The information
contained herein is designed only for the use of this unit. LAUNCH is not
responsible for any use of this information as applied to other units.
Statement: LAUNCH owns the complete intellectual property rights for the software
used by this product. For any reverse engineering or cracking actions against the
software, LAUNCH will block the use of this product and reserve the right to pursue
their legal liabilities.
Trademark Information
LAUNCH is a registered trademark of LAUNCH TECH CO., LTD. (also called
LAUNCH for short) in China and other countries. All other LAUNCH trademarks,
service marks, domain names, logos, and company names referred to in this
manual are either trademarks, registered trademarks, service marks, domain
names, logos, company names of or are otherwise the property of LAUNCH or
its affiliates. In countries where any of the LAUNCH trademarks, service marks,
domain names, logos and company names are not registered, LAUNCH claims
other rights associated with unregistered trademarks, service marks, domain
names, logos, and company names. Other products or company names referred
to in this manual may be trademarks of their respective owners. You may not use
any trademark, service mark, domain name, logo, or company name of LAUNCH
or any third party without permission from the owner of the applicable trademark,
service mark, domain name, logo, or company name. You may contact LAUNCH
by visiting the website at www.cnlaunch.com, or writing to LAUNCH TECH. CO.,
LTD., Launch Industrial Park, North of Wuhe Avenue, Banxuegang, Bantian,
Longgang, Shenzhen, Guangdong, P.R.China, to request written permission to
use Materials on this manual for purposes or for all other questions relating to
this manual.
General Notice
• Other product names used herein are for identification purposes only and
may be trademarks of their respective owners. LAUNCH disclaims any and all
rights in those marks.
• There is a possibility that this unit is inapplicable to some of the vehicle
models or systems listed in the diagnosis section due to different countries,
areas, and/or years. Do not hesitate to contact LAUNCH if you come across
such questions. We are to help you solve the problem as soon as possible.
ROXIE W
User Manual
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ROXIE W and is the answer not in the manual?

Questions and answers

Related Manuals for Launch ROXIE W

Summary of Contents for Launch ROXIE W

  • Page 1 Statement: LAUNCH owns the complete intellectual property rights for the software used by this product. For any reverse engineering or cracking actions against the software, LAUNCH will block the use of this product and reserve the right to pursue their legal liabilities.
  • Page 2 The right is reserved to make change at any time without notice. • Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs or expenses incurred by purchaser...

  • Page 3: Table Of Contents

    2.4 OBD II Readiness Monitors ................4 2.5 OBD II Monitor Readiness Status..............5 2.6 OBD II Definitions ...................5 3. Product Descriptions ..................7 3.1 Outline of ROXIE W..................7 3.2 Technical Specifications .................8 3.3 Accessories Checklist ..................9 4. Initial Use.......................10 4.1 Charging The Tool ..................10 4.2 Getting Started .....................10...
  • Page 4 LAUNCH ROXIE W User Manual 6.5 Diagnostic Software Upgrade ...............17 6.6 Expiration Date .....................18 6.7 Time Zone.....................18 6.8 Associate Device ..................18 6.9 Activation Code.....................18 6.10 System Version...................18 7. ROXIE-AIT Management Platform ...............19 7.1 Sign-up ......................19 7.2 Reports ......................21 7.3 My Devices ....................21 7.4 Settings......................23...

  • Page 5: Introduction

    User Manual 1. Introduction ROXIE W is an evolutionary smart plug & play solution which is specialized on automotive diagnostics. Users can achieve full vehicle system diagnosis without any operation, just simply plug the device into the vehicle’s DLC(Data Link Connector) directly and then keep the vehicle ignition key on.

  • Page 6: General Information

    LAUNCH ROXIE W User Manual 2. General Information 2.1 On-Board Diagnostics (OBD) II The first generation of On-Board Diagnostics (OBD I) was developed by the California Air Resources Board (ARB) and implemented in 1988 to monitor some of the emission control components on vehicles. As technology evolved and the desire to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed.

  • Page 7: Data Link Connector (Dlc) Location

    LAUNCH ROXIE W User Manual Figure 2-1 2.3 Data Link Connector (DLC) Location The DLC (Data Link Connector or Diagnostic Link Connector) is typically a 16- pin connector where diagnostic code readers interface with the vehicle’s on- board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles.

  • Page 8: Obd Ii Readiness Monitors

    LAUNCH ROXIE W User Manual Figure 2-2 2.4 OBD II Readiness Monitors An important part of a vehicle’s OBD II system is the Readiness Monitors, which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system.

  • Page 9: Obd Ii Monitor Readiness Status

    LAUNCH ROXIE W User Manual 6) Secondary air Injection 7) Heated Catalyst 8) A/C system 2.5 OBD II Monitor Readiness Status OBD II systems must indicate whether or not the vehicle’s PCM’s monitor system has completed testing on each component. Components that have been tested will be reported as “Ready”, or “Complete”, meaning they have been...
  • Page 10 LAUNCH ROXIE W User Manual DTC -- Diagnostic Trouble Codes (DTC) that identifies which section of the emission control system has malfunctioned. Enabling Criteria -- Also termed Enabling Conditions. They are the vehicle- specific events or conditions that must occur within the engine before the various monitors will set, or run.

  • Page 11: Product Descriptions

    LAUNCH ROXIE W User Manual 3. Product Descriptions 3.1 Outline of ROXIE W Figure 3-1 Name Descriptions DB-15 diagnostic To connect to vehicle's DLC (Data Link Connector) connector via diagnostic cable.

  • Page 12: Technical Specifications

    LAUNCH ROXIE W User Manual Indicates test results. • In Off mode, press it for about 5 seconds to turn the handset on. • In On mode: POWER key • Press it to activate the LCD if the LCD is off.

  • Page 13: Accessories Checklist

    LAUNCH ROXIE W User Manual 3.3 Accessories Checklist For detailed accessory items, please consult from the local agency. 1. ROXIE W handset 2. OBD II diagnostic cable 3. DC 5V charging cable 4. User manual 5. Power adaptor...

  • Page 14: Initial Use

    LAUNCH ROXIE W User Manual 4. Initial Use 4.1 Charging The Tool There are two charging methods available: Via Charging Cable: Plug one end of the included charging cable into the DC-IN port of the tool, and the other end to the external DC power.
  • Page 15 LAUNCH ROXIE W User Manual In Figure 4-1, tap “Next” to go to next step. 2. Select time zone : Tap to select the time zone of your current location, the system will automatically configure the system time according to the time zone you selected.
  • Page 16 LAUNCH ROXIE W User Manual address, and tap “Next” to go to next step. 100% Set-up Email After ROXIE is properly connected to the network and inspection is completed, the reports will be sent to the following email address. Carefully enter email address below (if you enter multiple email addresses, use “;”...
  • Page 17 “tag” on the reports. If you choose to skip this step, you may set it in “Settings” -> “Account Information” later. 6. Bind ROXIE W to a compatible diagnostic scanner : If you had purchased a diagnostic scanner of LAUNCH family, you can associate the ROXIE W device with it so that all diagnostic reports generated by ROXIE W can be viewed on the scanner.

  • Page 18: Diagnose

    LAUNCH ROXIE W User Manual 5. Diagnose 5.1 Connection 1. Turn the ignition off. 2. Locate vehicle’s DLC socket: It provides standard 16 pins and is generally located on driver’s side, about 12 inches away from the center of dashboard.

  • Page 19: View Reports

    LAUNCH ROXIE W User Manual Dec 17 08:59 100% VIN Scan VIN Identification function is reading the vehicle information... V Q B E V T R T E L B A N C L K J Stop Figure 5-2 *Note: To detect more and accurate VINs, a stable network connection is highly recommended for this function.
  • Page 20 For earlier reports, check your email for reference. LAUNCH cares about your data, however, LAUNCH will not be held liable for any data loss within your email as LAUNCH will only save reports for one year from the date the report was created.

  • Page 21: Settings

    Add, Revise and Delete operations are available. 6.3 Diagnostic Mode Use this item to assign the ROXIE W to execute the specific diagnostic operation to your preference. *Note: Alternatively, you can also set it as desired in “Settings” on the ROXIE-AIT management platform.

  • Page 22: Expiration Date

    6.8 Associate Device If you had purchased a diagnostic scanner of LAUNCH family, you can associate the ROXIE W device with it so that all diagnostic reports generated by ROXIE W can be viewed on the scanner. Enter the product S/N of the diagnostic scanner and tap “Save” to bind it.

  • Page 23: Roxie-Ait Management Platform

    LAUNCH ROXIE W User Manual 7. ROXIE-AIT Management Platform This platform is specially designed for workshops to better manage ROXIE / AIT series devices and view reports. 7.1 Sign-up 1. Open the browser, input https://usait.x431.com/getrepair to open the login page.
  • Page 24 LAUNCH ROXIE W User Manual *Note: Serial number is a 12-digit number starting with 98 – you can find it on the back of your tool. Verification code is a 8-digit number stored in the Private & Confidential sheet. After inputting all the info, click "Register" to bind the device to the current account, the Job Menu screen will be open automatically.

  • Page 25: Reports

    LAUNCH ROXIE W User Manual LAUNCH yihui.qiu@cnlaunch.com Reports Device S/N Please Select Please Enter VIN Please Enter Start Time Please Enter End Time Search My Devices S/N: 989760001031 VIN : WBAFG2102BL507724 View Report Settings DTC: Inspection Date: 09/26/2018 06:09:00 Change Password...
  • Page 26 LAUNCH ROXIE W User Manual LAUNCH yihui.qiu@cnlaunch.com Reports Add New Device My Devices S/N: 986990000223 Language : English Unbind Renew Settings Register Date: 12/12/2018 12:32:23 Service Valid Date: 06/20/2018 01:01:18 Change Password S/N: 989760001031 Language : English Unbind Renew Set Email...

  • Page 27: Settings

    Renewal Card, and then click "Confirm". All renewal records can be accessed and checked from "Settings" -> "Renewal Record". *Note: To avoid purchasing a forfeit Subscription Renewal Card, please purchase it from authorized LAUNCH dealers. 7.4 Settings Change Password: To modify the login password.
  • Page 28 LAUNCH ROXIE W User Manual Set Email: To set the Email address for receiving the diagnostic reports. Business Info: To add or revise the company information. Time Zone: To configure the time zone. Change Language: To change the audio prompt language of the ROXIE device during the diagnostic session.

  • Page 29: Faq

    LAUNCH ROXIE W User Manual 8. FAQ Here we list some frequently asked questions and answers related to this tool. System halts when reading data stream. What is the reason? It may be caused by a slackened connector. Please turn this tool off, firmly connect the connector, and switch it on again.
  • Page 30 The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.
  • Page 31 The device has been evaluated to meet general RF exposure requirement. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types Automotive AI Inspection Terminal with model ROXIE W (FCC ID: XUJROXIE) has also been tested against this SAR limit. The highest reported SAR values for body-worn is 1.19 W/kg.

Table of Contents