Sony HDC3500 Operating Instructions Manual page 8

a NETWORK TRUNK connector (RJ-45 8-pin) (common
to HKC-FB30)
Connects a device connected to the CCU's NETWORK
TRUNK connector to the network.
b DC power supply out connector (2-pin) (common to
HKC-TR37/HKC-FB30)
Supplies power to an external device up to 2.5 A.
c RET 1 (return video 1) button
The return video 1 signal from the camera control unit is
monitored on the viewfinder screen while this button is
pressed. It function the same as the RET 1 button on the
handle (page 7) and RET/ASSIGNABLE button A on the
operation panel on the rear of the camera (page 9 or 10).
You can also assign other functions to this button, using the
menu displayed on the viewfinder screen.
d MIC 1 IN (microphone 1 input) connector (XLR 3-pin)
Connect a microphone.
This connector and the AUDIO IN CH-1 connector (page 11)
on the operation panel on the rear of the camera are
alternately activated with the CH1 audio input select switch
(page 11).
e MIC (microphone) power switch
+48V: To supply a power of +48 V to the connected
microphone.
OFF: Not to supply a power to the connected microphone.
f SHUTTER switch
For setting the electronic shutter functions when the camera is
used in standalone status without connecting a camera control
unit.
OFF: The electronic shutter does not function.
ON: The electronic shutter is activated.
SEL: The shutter speed and shutter mode change each time
the switch is set to this position.
For details, see "Setting the Electronic Shutter" on page 17.
g INTERCOM LEVEL control
To adjust the intercom/earphone volume level.
The intercom level adjustment is enabled when the
INTERCOM 1 and 2 LEVEL/MIC switches (on the UCJ model
operation panel, page 9) or the LEVEL switch (on the
CE model operation panel, page 10) on the rear of the camera
are set to "FRONT."
h RET 2 (return video 2) button
When this button is pressed, the picture on the viewfinder
screen changes to the return video signal selected using RET/
ASSIGNABLE button A, B, or C on the operation panel on the
rear of the camera or using the menu.
You can also assign other functions to this button, using the
menu displayed on the viewfinder screen.
Rear
a
a CAMERA POWER switch
CCU: Power is supplied from the camera control unit.
EXT: Power is supplied through the DC IN connector.
b Tally lamp and switch
ON: The tally lamp lights when a tally signal is input to the
connected camera control unit or a call signal is
generated in response to pressing of a CALL button.
OFF: The tally lamp is prevented from lighting.
c RET 1/2 (return video 1/2) buttons
When pressed, the picture on the viewfinder screen changes
to the return video signal selected using the operation panel
on the rear of the camera or using the menu.
d CCU (camera control unit) connector
HDC3500/HKC-FB30: Connect a camera control unit using
an optical electrical multi cable.
When HKC-TR37 is attached: Connect a camera control unit
using a triax cable.
e SDI 1 (serial digital interface 1) connector (BNC-type)
(common to HKC-FB30)
For 3G SDI, HD SDI or HD PROMPTER signal output.
For details on the output signals, see "Setting the Camera
Outputs" (page 21).
f SDI 2 (serial digital interface 2) connector (BNC-type)
(common to HKC-FB30)
For 3G SDI or HD SDI signal output, or HD TRUNK signal
input.
During stand-alone operation, also used for inputting an
HD SDI return signal. When RET (return) is set to 1, this is
displayed in the viewfinder.
g-1 PROMPTER2 connector (BNC-type)
HDC3500/HKC-FB30: For prompter 2 signal output. Available
only when connecting a camera control unit with a
prompter 2 input connector.
g-2 SDI (serial digital interface) connector (BNC-type)
When HKC-TR37 is attached: 3G SDI signal or HD TRUNK
signal input.
8
b
Shoulder strap fitting
post (page 6)
Operation panel
(page 9)
c
d
e
f
g
Connector panel
(page 10)
h