Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Falco HES702
Summary of Contents for Falco HES702
- Page 1 Owner’s Manual STAINLESS STEEL PROFESSIONAL RANGE HOOD HES702(48INCH)
- Page 2 The Company warrants to the original purchaser that for the period of TWO YEAR on Barbeque (Braai) extractor model: HES702(48) from date of purchase the extractor should be free from defect under normal domestic use, both in workmanship and material.
-
Page 3: Safety Precautions
IMPORTANT SAFETY INSTRUCTIONS PLEASE READ ALL INSTRUCTION BEFORE USING SAFETY PRECAUTIONS WARNING! To reduce the risk of fire, electric shock or injury to persons, observe the following: A. Use this unit only in the manner intended by the manufacturer. If you have questions, please contact the manufacturer. - Page 4 following: A. Installation work and electrical wiring must be done by qualified persons in accordance with all applicable codes and standards, including fire-related construction B. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE),...
-
Page 5: Grounding Instructions
DUCTWORK READ AND SAVE THESE INSTRUCTION GROUNDING INSTRUCTIONS This extractor must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This extractor is equipped with a cord having a grounding wire with a grounding plug. - Page 6 previously set speed. However, when the function is active the LED flashes. By pressing any key for the exclusion of the hood light the hood will return immediately to its normal functioning. The “automatic stop timer” delays stopping of the hood, which will continue functioning for 15 minutes at the operating speed set at the time this function is activated.
- Page 7 •COMANDS PATTERN : A= Filtering system / Set clock B= Delay Timer C= Speed 1/ “-” adjust / off D= Digital display E= Speed 1/ “+” adjust / off F= Alarm G= Light When the Key A is flashing, at the same time “...
- Page 8 一、Instructions for use A == power on / off B == automatically stop the timer on / off C == stalls, counting time display D == sliding touch strips E == motor, automatic on / off F == lamps on / off Power on, press the A key, A key indicator lights, the All button to enter standby.
- Page 9 Care and Cleaning Baffle grease filters and drip trays metal baffles channel grease released by foods on the cook top into the trip trays. The baffles also help prevent flaming foods on the cook top from damaging the inside of the hood. For this reason, the baffles must ALWAYS be in place when the hood is used.
-
Page 10: Before You Begin
Stainless steel surface (on some models) Do not use a steel-wool pad, it will scratch the surface. 1. Shake bottle well 2. Place a small amount of professional Stainless Steel Cleaning Polish and Conditioner on a dry cloth or dry paper towel. 3. -
Page 11: Installation Clearances
INSTALLATION CLEARANCES These vent hoods are designed to be installed onto a wall or beneath a soffit or cabinet. ● Install these hoods*760mm Min. to 900mm Max. above the cooking surface. *These hoods may be installed 600mm min. above a gas or electric drop-in style cooktop. - Page 12 Use a level to draw a centerline from the bottom of the hood to ceiling or soffit. If venting out the ceiling ,extend the centerline forward on the ceiling or soffit Locate the centerline of a 267mm hole on the ceiling or soffit by measuring 153mm from the wall.
- Page 13 Fig. 6 FIXING OF THE EXHAUST DUCTING Important: • Remove the restrictive tape and make sure the blades are moving freely • Align the duct with the exhaust opening by using the provided 4 pieces of ST4X10 Philip thread screws •...
- Page 14 THE PROBLEM SOLVER PROBLEM POSSIBLE CAUSE Fan and lights do The hood was never electrically connected by the not operate when installer/electrician/builder. Call the switches are electrician/installer/builder to complete the installation. turned on This is not covered by warranty ...
- Page 15 filter does not correct problem, call for service. The halogen /heat The lamp or socket may be defective or a wire could be does lamps disconnected work 1. Do some trouble-shooting by removing the lamps and place it in the socket of a lamp that does work (the heat lamp will fit in the halogen socket for the purpose of checking it).
Need help?
Do you have a question about the HES702 and is the answer not in the manual?
Questions and answers