Setra Systems 269 Installation Manual page 4

6.0 EMC CERTIFICATION
This product complies with EN61326 Electrical Equipment for Measurement, Control and Laboratory use - EMC
Requirements for Minimum Requirements and Industrial Locations. Special caution should be taken to meet
Standard EN61000-4.5: 1995 Surge Immunity if any of the following conditions apply to the installation: The
product is installed outside; all or any part of the cable is exposed to the outside; the cable is greater than 30
meters in length. In order to meet the Surge Immunity Requirements, the following conditions must be
followed during installation:
1. Shielded cable must be used, and the shield must be tied to earth ground (not power supply
ground) on at least one end of the cable shield/drain wire. The shield must be maintained all the
way from sensor to the power supply.
2. If unshielded cable is used, an earth grounded metal conduit fitting can be used to replace the
shielded cable.
3. For a sensor with a metal body or enclosure, the body/enclosure must be ground to earth. If a
protective metal housing is used, the metal housing should be grounded to earth.
4. If a protective plastic housing is used, the housing must be able to withstand at least 2 KV from
the housing to earth ground, without damaging the circuit.
7.0 RETURNING PRODUCTS FOR REPAIR
Please contact a Setra application engineer (800-257-3872, 978-263-1400) before returning unit for repair to
review information relative to your application. Many times only minor field adjustments may be necessary.
When returning a product to Setra, the material should be carefully packaged and shipped prepaid to:
To assure prompt handling, please supply the following information and include it inside the package or
returned material:
1.
2.
3.
4.
Notes: Please remove any pressure fittings and plumbing that you have installed and enclose any required
mating electrical connectors and wiring diagrams.
Allow approximately 3 weeks after receipt at Setra for the repair and return of the unit.
Non-warranty repairs will not be made without customer approval and a purchase order to cover repair
charges.
Setra maintains a complete calibration facility that is traceable to the National Institute of Standards &
Technology (NIST). If you would like to recalibrate or recertify your Setra pressure transducers or transmitters,
please call our Repair Department at 800-257-3872 (978-263-1400) for scheduling.
8.0 WARRANTY AND LIMITATION OF LIABILITY
SETRA warrants its Model 269 products to the original consumer purchaser against defects for a period of one
year from the date of sale by SETRA, as shown in its shipping documents. Without charge, SETRA will repair or
replace products found to have manufacturing defects within the warranty period.
The serial number or date code must not have been removed, defaced or otherwise changed.
SETRA must be notified in advance of any returns; any products returned to SETRA must be transportation
prepaid.
The foregoing warranty is in lieu of all warranties, express, implied or statutory, including but not limited to, any
implied warranty of merchantability for a particular purpose.
SETRA's liability for breach of warranty is limited to repair or replacement, or if the goods cannot be repaired or
replaced, to a refund of the purchase price. SETRA's liability for all other breaches is limited to a refund of the
purchase price. In no instance shall SETRA be liable for incidental or consequential damages arising from a
breach of warranty, or from the use or installation of its products.
No representative or person is authorized to give any warranty other than as set out above or to assume for
SETRA any other liability in connection with the sale of its products.
159 Swanson Road, Boxborough, MA 01719-1304
Tel: 800-257-3872/978-263-1400
SS2135 Rev. D 7/19/07
4
Setra Systems, Inc.
159 Swanson Road
Boxborough, MA 01719-1304
Attn: Repair Department
Name and phone number of person to contact.
Shipping and billing instructions.
Full description of the malfunction.
Identify any hazardous material used with product.
Calibration Services

ISO
9001:
2000
Certified