Table of Contents
Advertisement
Installation Instruction and Owners Manual
BLASTER SALT/SAND SPREADERS
Models: 350/350S/750/750R/750S & 750RS
Meyer Products LLC reserves the right, under its continuing product improvement program, to change construction or design details,
specifications and prices without notice or without incurring any obligation.
© 2011 Printed in the U.S.A.
BLASTER 350 (32000)
350S (37000)
BLASTER 750(33000)
750R(33750)
750S (39000)
750RS (39010)
Meyer Products LLC
18513 Euclid Ave. • Cleveland, Ohio 44112-1084
Phone 486-1313 (Area Code 216)
www.meyerproducts.com• email info@meyerproducts.com
Form 1-915 R3
November 2011
Advertisement
Table of Contents
Related Manuals for Meyer Blaster 350
Summary of Contents for Meyer Blaster 350
- Page 1 750RS (39010) BLASTER 350 (32000) 350S (37000) Meyer Products LLC reserves the right, under its continuing product improvement program, to change construction or design details, specifications and prices without notice or without incurring any obligation. Meyer Products LLC 18513 Euclid Ave. • Cleveland, Ohio 44112-1084 Phone 486-1313 (Area Code 216) www.meyerproducts.com•...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ....................1 VEHICLE REQUIREMENTS ................1 SAFETY GUIDELINES ..................2 350 & 350S PARTS LIST ..................3 INSTALLING RECEIVER MOUNT MODEL: 350/350S/750R/750RS....4 750 & 750S PARTS LIST ..................5 750R & 750RS PARTS LIST ................6 ELECTRICAL INSTALLATION ................ -
Page 3: Introduction
Our high torque, direct drive motor powered by a state-of-the-art, variable speed, solid state electronic controller will provide reliable power and control when spreading, even at extremely low temperatures. Meyer Products LLC reserves the right to make any changes or improve the design of any parts and not be obligated to make changes on units previously sold. -
Page 4: Safety Guidelines
SAFETY GUIDELINES For you safety when the word WARNING is used, this refers to information that if not carefully followed could result in personal injury or death. The word CAUTION refers to a situation that could cause minor injury or damage to equipment. WARNING –... -
Page 5: 350 & 350S Parts List
Blaster 350/350S Note: Auger Extension (16) must be removed when using salt only. If it is not removed this may cause the motor to stall. Speed Control Mounting Bracket Blue White White Ground Pigtail Spreader Motor Battery Black Parts List... -
Page 6: Installing Receiver Mount Model: 350/350S/750R/750Rs
350/350S/750R/750RS The Blaster 350/350S/750R/750RS is a dedicated, Class 3, receiver (hitch) mount salt spreader. Prior to installation, be certain that the vehicle receiver is in good working order, is rated for at least a 500 lb. tongue load, and is fastened to the vehicle securely. -
Page 7: 750 & 750S Parts List
Blaster 750/750S Note: Auger Extension (15) must be removed when using salt only. If it is not removed this may cause the motor to stall. Speed Control Mounting Bracket Blue White White Ground Pigtail Spreader Motor Battery Black Parts List 750S 750S Item... -
Page 8: 750R & 750Rs Parts List
Blaster 750R & 750RS Speed Control Mounting Bracket Blue White White Ground Pigtail Spreader Motor Battery Black Parts List 750R 750RS 750R 750RS Item Part No. Part No. Qty. Description Item Part No. Part No. Qty. Description 33750 39010 Blaster Assembly --------- 34601 •... -
Page 9: Electrical Installation
ELECTRICAL INSTALLATION FOR ALL BLASTER SERIES SPREADERS 1.) Locate the wire harness and begin to route it from the rear of the vehicle to the front. The molded rubber plug indicates the rear of the harness, closest to the spreader. Use frame holes and frame supports as lashing points. Do not attach to fuel or brake lines. -
Page 10: Operating The Spreader
OPERATING THE SPREADER Before using the spreader read and understand all aspects of this operators manual. PREPARATION CAUTION – Sweep area clear of foreign objects or obstacles that could cause personal injury. Keep other persons and animals out of area to be spread. SPREADER LOADING Your spreader will come equipped with a cover that will protect your de-icing material from rain or snow;... -
Page 11: Spreader Maintenance
TROUBLESHOOTING If your spreader is not operating properly, take it to your local Meyer Products Distributor for maintenance or service. However, that is not always possible, so below on this page you will find a troubleshooting guide, which can assist you in determining the problem. -
Page 12: Warranty Information
Meyer Products’ liability will be no more than the amount you paid for the product that is the subject of a claim; this is the maximum amount for which we are responsible.
Need help?
Do you have a question about the Blaster 350 and is the answer not in the manual?
Questions and answers