Blizzard Power Plow 8611 Assembly & Operation Manual page 24

Ref. Part Qty. Part Description
No. Number
1 52122 1 Moldboard Weldment
2 61086 1 Label, WARNING! (BLZ 1005)
3 61082 1 Decal, Center Moldboard (BLZ 1000)
4 61180 1 Label, Power Hitch™ Mounting & Dismounting Instructions (BLZ 1023)
5 11962 1 Cutting Edge (1080), Moldboard
6 61196 7 Bolt, Carriage, 1/2"-13 x 1-1/2" Grade 8 P
7 61365 13 Nut, Flanged Lock, 1/2"-13
8 51100 1 Wing Weldment, Driver's Side
9 63065 1 Decal, Wing, Driver's Side (BLZ 1033)
10 51069 1 Cutting Edge Weldment (T1), Wing, Driver's Side
11 50075 1 Slide Box Weldment, Driver's Side
12A 61220 2 Plow Shoe Assembly, Heavy-Duty Cast Iron (8-3/8" Shaft): (1) - 12 & 14, (18) - 13
12 61102 2 Spacer, 1-5/8" O.D., 1-1/8" I.D. x 1-1/2" YZ
13 61101 36 Washer, Flat, 1", 1-3/4" O.D., 1-1/16" I.D. YZ
14 61103 2 Pin, Linch, 1/2" x 1-3/4"
15 63063 1 Label, Serial Number, Sequentially Numbered (BLZ 1049)
16 61383 4 Screw, Hex Head Cap, 5/16"-18 x 2-1/4" Grade 8 YZ
17 61384 4 Nut, Top Lock, 5/16"-18 Grade C Z
18 11871 4 Pin, Slide Box Stop, 1" DIA. x 4-3/4" (with 3/8" DIA. hole)
19A 61049 2 Plow Guide Assembly: (2) - 19 & 20
19 61051 4 Screw, Hex Head Cap, 5/16"-18 x 1" Grade 5 Z
20 61052 4 Nut, Nylon Insert Lock, 5/16"-18 Z
21 51101 1 Wing Weldment, Passenger's Side
22 63064 1 Decal, Wing, Passenger's Side (BLZ 1032)
23 51070 1 Cutting Edge Weldment (T1), Wing, Passenger's Side
24 61360 2 Bolt, Carriage, 1/2"-13 x 5" Grade 8 P
25 61361 2 Bolt, Carriage, 1/2"-13 x 5-1/2" Grade 8 P
26 61362 2 Bolt, Carriage, 1/2"-13 x 6-1/2" Grade 8 P
27 50074 1 Slide Box Weldment, Passenger's Side
28 61416 2 Bolt, Spade, 5/8"-11 x 7-3/8" Grade 8 Z
29 61099 8 Spring, Extension, 15-1/4" O.A.L. x 2-3/8" O.D. x 3/8"
30 61385 2 Pin, Clevis, 5/8" DIA. x 3" YZ
31 61028 2 Pin, Spring, 1/4" DIA. x 1-1/4"
32 13307 2 Pin, Wing / Slide Box Pivot, 1" DIA. x 11-1/8"
33 60207 2 Hydraulic Cylinder, Slide Box Extend/Retract
34 61063 2 Nut, Top Lock, 5/8"-11 Grade C Z
35 60003 4 Hydraulic Adapter, 7/16"-20 x 9/16"-18 Male O.R.B. Connector
36 60019 2 Hydraulic Hose (Ports #7 & #10), 1/4" x 36" - Slide Box Retract
37 60007 7 Hydraulic Adapter, 9/16"-18 x 9/16"-18 Male O.R.B. Connector
38 60224 2 Hydraulic Hose (Ports #8 & #9), 3/8" x 36" - Slide Box Extend
39 61198 2 Cap, 5/8" I.D., 3/4" O.D. x 1", Black Vinyl
40 11989 2 Pin, Hydraulic Cylinder Base End, 5/8" DIA. x 11-1/2" (with 1/4" DIA. hole) - Slide Box Extend/ Retract
41 61030 2 Pin, Hair Cotter, 1/8" DIA. x 2-5/8" Z
42 61187 6 Bolt, Spade, 5/8"-11 x 6-3/8" Grade 8 Z
43 61064 6 Washer, SAE Mil Carb High-Strength, 5/8", 1-5/16" O.D., 21/32" I.D. YZ
44 61188 6 Nut, Nylon Insert Lock, 5/8"-11 Type NE
45 41052 1 Pivot Beam Weldment
46 61357 8 Pin, Cotter, 1/4" x 1-1/2" Z
47A 41039 1 Kickstand Assembly: (1) - 47 & 48, 52-54, (2) - 49 & 50, (3) - 51
47 41047 1 Kickstand Foot Weldment
48 41038 1 Kickstand Leg Weldment
49 61057 2 Screw, Hex Head Cap, 1/2"-13 x 1-1/4" Grade 8 YZ
50 61026 2 Washer, SAE Mil-Carb High-Strength, 1/2", 1-1/16" O.D., 17/32" I.D. YZ
51 61020 3 Nut, Top Lock, 1/2"-13 Grade C Z
52 61152 1 Screw, Hex Head Cap, 1/2"-13 x 4-1/2" Grade 8 YZ
53 61293 1 Spring, Compression, 2" O.A.L. x 1.101" O.D., 0.207" Wire Diameter
54 41037 1 Bushing, Stepped, 1.13" O.D., 0.53" I.D. x 3/8" Stainless Steel
55 50069 2 Pin, Clevis, 3/4" DIA. x 3" YZ
56 41051 4 Pin, Clevis, 3/4" DIA. x 5" YZ
57 61330 1 Screw, Hex Head Cap, 1"-8 x 9" (with 7-3/4" Shank) Grade 8 P
58 61008 1 Nut, Top Lock, 1"-8 Grade C Z
59 61217 4 Grommet, 1-1/2" I.D., 2-1/8" O.D. Black Rubber, 60 Durometer
60 60221 2 Hydraulic Cylinder, Plow Angle
61 60223 2 Hydraulic Hose (Ports #1 & #2), 3/8" x 24" - Plow Angle
62 60005 3 Hydraulic Adapter, 9/16"-18 x 9/16"-18 90˚ Adjustable Elbow O.R.B.
63 60237 1 Hydraulic Cylinder, Plow Raise/Lower
22 Parts List (1 of 4)
M O D E L 8 6 1 1 PA R T S L I S T
Moldboard & Wing Assembly Parts
Pivot Beam & A-frame Assembly Parts
Note: The reference numbers listed
identify parts shown in the illustration
on pages 26-28. These numbers are
specific to these illustrations only and
do not correspond with other diagrams
in the manual. Always review the part
number given for proper component
identification.