Yamaha RIVAGE PM7 Systems Setup Manual page 50

Analog Input Characteristics
Input Jack Gain
+66 dB
OMNI IN 1-8
–6 dB
+54 dB
TALKBACK
–6 dB
*1. Sensitivity is defined as the input level required to produce an output of +4 dBu (1.23 V) or the nominal output level when all faders
and level controls are set to maximum.
*2. Connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*3. 0 dBu=0.775 Vrms for all specifications
*4. All AD converters are 24-bit linear.
*5. OMNI IN jacks 1-8 and the TALKBACK XLR jack feature +48 V DC phantom power, which is switchable for each jack individually from
the unit's software.
Analog output characteristics
Output
Output Jack
Impedance
OMNI OUT
75Ω
1-8
PHONES
15Ω
A, B
*1. The unit features an internal switch to change the maximum output level.
*2. The +24dBu switch position can be changed for fee so that the output level will be +20 dBu.
For more information, contact your Yamaha dealer.
*3. Connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*4. These measurements were obtained when the PHONES A/B LEVEL knobs are set 10 dB lower than the maximum.
*5. Connectors are unbalanced. (Tip=LEFT, Ring=RIGHT, Sleeve=GND)
*6. 0 dBu=0.775 Vrms for all specifications
*7. All DA converters are 24-bit linear.
Digital I/O characteristics
Jack
AES/EBU IN 1/2, 3/4, 5/6, 7/8
AES/EBU OUT 1/2, 3/4, 5/6, 7/8
*1. Features sampling rate converters.
• Input SRC
Supported input frequency (conversion source): 44.1 kHz-4%-200 ppm – 96 kHz+4.1667%+200 ppm
• Output SRC
Supported output frequency (conversion destination): 44.1 kHz-4%-200 ppm – 96 kHz+4.1667%+200 ppm
*2. Connectors are balanced. (1=GND, 2=HOT, 3=COLD)
50 RIVAGE PM7 System Setup Guide
*3*4*5
Input Source
Impedance Impedance
50-600Ω Mics
10 kΩ
& 600Ω Lines
50-600Ω Mics
10 kΩ
& 600Ω Lines
*6*7*8
Max Output
Load
Level Select
Impedance
*1*2
Switch
+24 dBu
(default)
600Ω Lines +18 dBu
+15 dBu
8Ω Phones —
40Ω Phones —
Format Data Length
*1
AES/EBU 24 bit
*1
AES/EBU 24 bit
Input Level
*1
Sensitivity Rated Level
–82 dBu –62 dBu
(61.6μV) (0.616 mV)
–10 dBu +10 dBu
(245 mV) (2.45 V)
–70 dBu –50 dBu
(245 μV) (2.45 mV)
–10 dBu +10 dBu
(245 mV) (2.45 V)
Output Level
Max. Level
Rated Level Before
Clipping
+4 dBu +24 dBu
(1.23 V) (12.3 V)
–2 dBu +18 dBu
(0.616 V) (6.16 V)
–5 dBu +15 dBu
(0.436 V) (4.36 V)
*4
75 mW 150 mW
*4
65 mW 150 mW
Level
RS422 XLR-3-31 type
RS422 XLR-3-32 type
Max. Level
Connector
Before
Clipping
–42 dBu
(6.16 mV)
*2
XLR-3-31 type
+30 dBu
(24.5 V)
–30 dBu
(24.5 mV)
*2
XLR-3-31 type
+30 dBu
(24.5 V)
Connector
*3
XLR-3-32 type
Stereo Phone Jack
*5
(TRS)
Connector Balanced / Unbalanced
*2
Balanced
*2
Balanced
Balanced /
Unbalanced
Balanced
Balanced
Balanced /
Unbalanced
Balanced
Unbalanced