Texmate UM-35-CL Manual

General Features

T e - 5- an co t-e ect e - 0m
n mete . It ea l e a
-1999 and +1999 with header selectable signal conditioning.
Typical Application Connections
4 to 20mA Process Loop Measurement
Other devices can be
added to the loop.
PIN 2
_
+
24V
Common
External
Loop Supply
Fully User Scalable
Order IP02, if you require the loop
excitation voltage to be supplied by the meter.
UM-Series utility meters for switchboard and process indication
UM-35-ACA ....AC amps, Scaled or True RMS, (1 or 5 Amp internal shunt), 3.5 digit.
UM-35-ACV ......AC volts, Scaled or True RMS. 199.9V AC/700V AC header selectable ranges,
3.5 digit.
UM-35-DCA ....DC mV ±20mV/±50mV/ ±100mV/±200mV header selectable ranges, 3.5 digit
UM-35-DCV .....DC Volts ±2V/±20V/±200V DC header selectable ranges, 3.5 digit.
UM-40-ACA ....AC amps, Scaled or True RMS, (1 or 5 Amp internal shunt), 4.0 digit.
UM-40-ACV ....AC volts, Scaled or True RMS. 199.9V AC/700V AC header selectable ranges,
4.0 digit.
UM-45-DCA .....DC mV ±20mV/±50mV/ ±100mV/±200mV header selectable ranges, 4.5 digit
UM-45-DCV ....DC Volts ±2V/±20V/±200V DC Header selectable ranges, 4.5 digit.
UM-35-CL manual (UM04)
Optional super
bright LEDs
oce loo mea-
ta le to an ea n etween
Offset
< Decrease Zero Increase >
ON
OFF
HI
LO
< Decrease Span Increase >
Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com
UM-Series
UM-35-CL
4-20mA Process Loop
3 1/2 DIGIT with 0.56" LEDs
in a NEMA type 1 Style Case
Reliable Process Loop indicator with scal-
able capabilities from -1999 to +1999 to
represent any engineering units, FLOW,
LEVEL, TEMPERATURE, PRESSURE.....

Specifications

Input Configuration: ........Series connection to 4-20mA process loop.
Full Scale Ranges: ..........User adjustable to any scaling between
Input Impedance: .............70 .
A/D Converter: .................12 Bit Dual Slope
Accuracy: .........................±(0.05% of reading + 2 counts)
Temperature Coefficient: 100 ppm/°C (Typical)
Warm Up Time: ................2 minutes to specified accuracy
Conversion Rate: .............3 conversions per second (Typical)
Display:.............................3 1/2 digit 0.56" Red LED display (std),
Polarity: ............................Bipolar. Assumed positive displays negative.
Decimal Selection: .......... ea e
Over-range Indication: .... (
Power Supply (std): .........
( tn) - I ..........I olate
Operating Temperature: ..–10 to 50 °C
Storage Temperature: .....–20 to 70 °C.
Relative Humidity: ...........95% (non-condensing)
Case Dimensions: ........... e el .78
Weight: .............................
UM-35-CL .......Process 4 to 20mA (100.0), optional 24V DC excitation ,easily user
scalable in engineering units from –1999 to +1999. 3.5 digit
UM-35-HZ .......15Hz to 199.9Hz or optional 40Hz to 400Hz up to 500V AC , 3.5 digit.
UM-35-Pressure..Pressure, strain gage and load cell, 4 and 6 wire, 5V DC excitation,
Header Selectable Sensitivity 2mV/V, 5mV/V, 10mV/V, 20mV/V, 3.5 digit
UM-35-JF ........J thermocouple input, 1° resolution, order °C or °F, 3.5 digit
UM-35-KF .......K thermocouple input, 1° resolution, order °C or °F, 3.5 digit
UM-35-RTD/F ..100Ω platinum RTD, 3 or 4 wire, order °C or °F and 0.1° or 1°, 3.5 digit
UM-45-CL .......Process 4 to 20mA (100.0), optional 24V DC excitation ,easily user
scalable in engineering units from –19999 to +19999. 4.5 digit
-1999 to +1999.
ax m m . o
Green or Super Bright Red are optional.
Range -1999 to 1999 counts.
n e ace late, • • • •
) la e all ot e
0 0 , 50 60 00 . a
w tc e . 9 to 6 to
x .89 (96mm x 8mm)
e t e n e el . 6 (8 .5mm) l
0.5 to .9 ( .7 to .8mm) e en n on
connector used.
. o (0. )
5.6o (0. ). w en ac e .
t lan
ox .5 .
Page 1