MTU 12V4000M93 series Operating Instructions Manual page 6

7.2 Engine
7.2.1 Engine - Barring manually
7.2.2 Barring engine with starting system
7.3 Cylinder Liner
7.3.1 Cylinder liner - Endoscopic examination
7.3.2 Cylinder liner - Instructions and comments on
endoscopic and visual examination
7.4 Crankcase Breather
7.4.1 Crankcase breather - Oil mist separator
replacement
7.5 Valve Drive
7.5.1 Valve gear - Lubrication
7.5.2 Valve clearance - Check and adjustment
7.5.3 Cylinder head cover - Removal and
installation
7.6 Injection Pump / HP Pump
7.6.1 HP fuel pump - Filling with engine oil
7.6.2 HP fuel pump - Relief bore check
7.7 Injection Valve / Injector
7.7.1 Injector - Replacement
7.7.2 Injector - Removal and installation (jacketed
fuel system)
7.8 Fuel Filter
7.8.1 Fuel filter - Replacement
7.8.2 Fuel prefilter - Differential pressure gage
check and adjustment
7.8.3 Fuel prefilter - Draining
7.8.4 Fuel prefilter - Flushing
7.8.5 Fuel prefilter with water separator - Filter
element replacement
7.9 Exhaust Turbocharger
7.9.1 Compressor wheel - Cleaning
7.10 Charge-Air Cooling
7.10.1 Intercooler - Checking condensate drain for
coolant leakage and obstruction
7.11 Air Filter
7.11.1 Air filter - Replacement
7.11.2 Air filter - Removal and installation
7.12 Air Intake
7.12.1 Contamination indicator - Signal ring position
check
7.13 Starting Equipment
7.13.1 Starter - Condition check
7.14 Lube Oil System, Lube Oil Circuit
7.14.1 Engine oil level - Check
7.14.2 Engine oil - Change
7.14.3 Engine oil - Sample extraction and analysis
7.15 Oil Filtration / Cooling
7.15.1 Automatic oil filter - Overview
7.15.2 Oil indicator filter - Cleaning
4 | Table of Contents | MS150047/05E 2018-08
156
7.15.3 Oil indicator filter - Cleaning and check
7.15.4 Centrifugal oil filter - Cleaning and filter-
156
sleeve replacement
157
7.16 Coolant Circuit, General, High-Temperature
158
Circuit
158
7.16.1 Venting points
160 7.16.2 Engine coolant - Level check
7.16.3 Engine coolant - Change
162
7.16.4 Engine coolant draining
7.16.5 Engine coolant - Filling
162
7.16.6 Engine coolant pump - Relief bore check
163 7.16.7 Engine coolant - Sample extraction and
analysis
163
164
7.17 Raw Water Pump with Connections
7.17.1 Raw water pump - Relief bore check
168
7.18 Battery-Charging Generator
169
7.18.1 Battery-charging generator drive - Coupling
169
condition check
171
7.19 Engine Mounting / Support
172
7.19.1 Engine mounting - Checking resilient element
172
7.20 Auxiliary PTO
173 7.20.1 Bilge pump - Relief bore check
180 7.21 Fuel Supply System
180 7.21.1 Water drain valve - Check
7.21.2 Differential pressure gage - Alarm function
182 check
183 7.21.3 Water level probe (3-in-1 rod electrode) -
185 Check
7.21.4 Pump capacity - Check
187 7.21.5 Coalescer filter element - Replacement
190 7.22 Wiring (General) for Engine/Gearbox/Unit
190 7.22.1 Engine cabling - Check
194 7.23 Accessories for (Electronic) Engine
Governor / Control System
194
7.23.1 CDC parameters - Reset with DiaSys®
7.23.2 EMU and connectors - Cleaning
196
7.23.3 Limit switch for start interlock - Check
196
7.23.4 Engine governor and connector - Cleaning
197
7.23.5 Engine Control Unit ECU 7 - Checking plug
198
connections
7.23.6 Engine Monitoring Unit EMU 8 - Plug
connections check
198
7.23.7 Interface module EIM plug connections -
199
Check
199
7.23.8 Engine governor ECU 7 - Removal and
installation
200
7.23.9 Engine Monitoring Unit EMU 8 - Removal and
200
installation
201
7.23.10 Engine Interface Module EIM 2 - Removal and
203
installation
204
7.23.11 Engine Interface Module EIM 2 - Diagnostic
204
features
207
209
211
213
213
214
216
217
218
220
221
222
222
223
223
224
224
225
225
226
226
227
228
229
230
232
232
233
233
234
235
236
237
238
239
240
241
242
243