STANLEY Engineered Fastening. The information provided is based on the data known at the moment of the introduction of this product. STANLEY Engineered Fastening pursues a policy of continuous product improvement and therefore the products may be subject to change. The information provided is applicable to the product as delivered by STANLEY Engineered Fastening.
• Do not use outside the design intent of Placing STANLEY Engineered Fastening Blind Fasteners. Use only parts, fasteners, and accessories recommended by the manufacturer. • Use Power Tool only with specifically designated battery packs. • 1.2. POWER TOOL USE AND CARE The tool must be maintained in a safe working condition at all times and examined at regular intervals for damage and •...
CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT®/POP®Avdel® rechargeable batteries. Other types of batteries may burst causing personal injury and damage. CAUTION: Children should be supervised to ensure that they do not play with the appliance. NOTICE: Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material.
• Do not discard batteries into water. WARNING: Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on).
Page 6
DeWALT/POP-Avdel charger may make them burst or lead to other dangerous situations. Risk of electric shock. STANLEY Engineered Fastening policy is one of continuous product development and improvement and we reserve the right to change the specification of any product without prior notice.
STANLEY Engineered Fastening policy is one of continuous product development and improvement and we reserve the right to change the specification of any product without prior notice. Nose Assemblies Nose equipment varies according to the blind rivet type being installed. Each nose assembly represents a unique set of components which can be ordered individually.
Page 8
Placing capacity chart PB3400 Rivet Type 4.8mm 6.4mm 8.0/9.0 6.0 mm [3/16´´] [1/4´´] ● OPEN END ● ● CLOSED END ● AVEX®/ ● ● STAVEX® AVINOX®/ ● ● ● AVIBULB® HR/HT ● ● INTERLOCK® ● Hemlok® KLAMP-TITE®/ ● ● ● BULBEX®/LS/TL ●...
Page 9
Nose piece chart Material (Body/Mandrel) Rivet size Rivet Type Al/St NiCu/St St/St Al/Al SS/SS Al/SS NiCu/SS SS/St TP124-542*** TP124-542*** TP124-542*** TP124-542*** TP124-542*** Open End TP143-648* TP143-648* TP143-648* TP143-648* TP143-648* TP124-542*** Closed End TP124-546*** TP124-546*** TP124-546*** TP143-648* TP124-542*** AVEX Ⓡ TP143-648* TP124-542*** TP124-542*** STAVEX...
Page 10
Bold : Equipped on the tool Grey : Included with Standard Kit Material (Body/Mandrel) Rivet size Rivet Type Al/St NiCu/St St/St Al/Al SS/SS Al/SS NiCu/SS SS/St TP144-593*** TP144-593*** TP144-593*** Open End TP143-646 TP143-646 TP143-646 Closed End TP144-640*** TP144-593*** AVEX Ⓡ TP143-646 TP144-593*** STAVEX...
Page 11
Jaw and Jaw pusher chart Bold : Equipped on the tool Rivet size Rivet type SA Nose housing SA Jaw Pusher Mandrel Guide TP143-594* Open End Closed End(SS/SS) TP143-643 Closed End(Al/Al, Al/St, St/St) TP143-594* AVEX Ⓡ TP143-594* STAVEX Ⓡ TP143-643 HRrivets (Al/St, Al/SS) Ⓡ...
Page 12
Bold : Equipped on the tool Rivet size Rivet type SA Nose housing SA Jaw Pusher Mandrel Guide TP143-594* Open End TP143-643 Closed End TP143-594* TRM00502 TRM00393 AVEX Ⓡ TP143-594* STAVEX Ⓡ TP143-643 HRrivets (Al/St) Ⓡ TP143-594* TP144-655* Unnecessary** HRrivets (St/St) Ⓡ...
Need help?
Do you have a question about the ProSet PB3400 and is the answer not in the manual?
Questions and answers