Stanley 76003 Instruction Manual
Hydro-pneumatic power tool
Hide thumbs
Also See for 76003:
- Instruction manual (213 pages) ,
- Service manual (24 pages) ,
- Instruction manual (59 pages)
Related Manuals for Stanley 76003
Summary of Contents for Stanley 76003
- Page 1 Instruction manual ProSet® XT3 Blind Rivet Tool – 76003 ProSet® XT4 Blind Rivet Tool – 76004 Hydro-Pneumatic Power Tool...
- Page 2 Figure 1 Figure 2...
- Page 3 Figure 3 Figure 5 Figure 4 Figure 6...
-
Page 4: Table Of Contents
All rights reserved. The information provided may not be reproduced and/or made public in any way and through any means (electronically or mechanically) without prior explicit and written permission from XXX. The information provided is based on the data known at the moment of the introduction of this product. XXX pursues a policy of continuous product improvement and therefore the products may be subject to change. -
Page 5: Safety Definitions
1. SAFETY DEFINITIONS The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. -
Page 6: Specification
Never leave operating tool unattended. Disconnect air hose when tool is not in use. Adequate clearance is required for the tool operator’s hands before proceeding. Do not abuse the tool by dropping or using it as a hammer. ... -
Page 7: The Package Contains
Is only applicable for XT4 tool (3) Non-standard nose equipment required. For a full list of compatible nose equipment for each rivet type, together with assembly and maintenance instructions, please refer to the ProSet® nose equipment manual 07900-09414 2.3 THE PACKAGE CONTENTS ... -
Page 8: Main Component List
6.4 mm [1/4”] rivets. 1 Printed Instruction Manual – region dependent. 2.4 MAIN COMPONENTS LIST Refer to figure 1 & 2 and the table below. Item Part Number Description 76003-15000 Standard nose equipment 76003-02022 Suspension hook 76003-05200 Mandrel collector 07001-00405... -
Page 9: Nose Equipment
IMPORTANT - THE AIR SUPPLY MUST BE TURNED OFF OR DISCONNECTED BEFORE FITTING OR REMOVING THE NOSE ASSEMBLY. 3.1 NOSE EQUIPMENT (Ref. fig. 2) Item numbers in bold refer to the components in figures 1 & 2 and the tables on page 5. The complete tool will be supplied pre-assembled with the Nose Piece for 4.8mm [3/16”] rivets. -
Page 10: Principle Of Operation
Air supply hoses will have a minimum working effective pressure rating of 150% of the maximum pressure produced in the system or 10 bar, whichever is the highest. Air hoses must be oil resistant, have an abrasion resistant exterior and be armoured where operating conditions may result in hoses being damaged. -
Page 11: Emptying The Mandrel Collector
CAUTION - DO NOT USE THE TOOL WHEN THE MANDREL COLLECTOR IS REMOVED The tool is fitted with a quick connect/release mandrel collector (3). A 60 rotation removes or replaces the mandrel collector. Removing the mandrel collector (3) from the tool automatically turns OFF the vacuum rivet retention and mandrel extraction system. -
Page 12: Declaration Of Conformity
UNITED KINGDOM, declare under our sole responsibility that the product: Description POP®Avdel® Hydro-Pneumatic Tool for Blind Rivets Brand/Model ProSet® XT3 P/N 76003-02000 and ProSet® XT4 P/N 76004-02000 Serial No. to which this declaration relates is in conformity with the following standard: ISO 12100:2010... -
Page 13: Protect Your Investment. Warranty Registration
XXX Engineered Fastening Avdel UK Limited 7.1 POP®Avdel® BLIND RIVET TOOL WARRANTY XXX House, Works Road XXX warrants that all power tools have been carefully manufactured and that they will be free from defect in Letchworth Garden City, Hertfordshire SG6 1JY material and workmanship under normal use and service for a period of one (1) year. - Page 14 The names and logos of other companies mentioned herein may be trademarks of their respective owners. Data shown is subject to change without prior notice as a result of continuous product development improvement policy. Your local STANLEY Engineered Fastening representative is at your disposal should...
Need help?
Do you have a question about the 76003 and is the answer not in the manual?
Questions and answers
CAN I INSTALL A NAS192106S05 BLIND RIVET WHICH IA A RIVET THAT IS .198 IN DIAMETER AND THE PULL ROD IS APOX .147 IN DIA