Download  Print this page

JTS SIEM-2T User Manual

Uhf pll mono in ear monitoring system
Hide thumbs

Advertisement

Hear The Future......Now !
UHF PLL Mono In Ear Monitoring System
UHF PLL M
no In Ear Monitoring System
1856
59508-031

Advertisement

Table of Contents
loading

  Related Manuals for JTS SIEM-2T

  Summary of Contents for JTS SIEM-2T

  • Page 1 Hear The Future..Now ! UHF PLL Mono In Ear Monitoring System UHF PLL M no In Ear Monitoring System 1856 59508-031...
  • Page 2 ATTENTION Please pay high attention to the following information. Sound Level (dB) Duration per day (hrs) The guideline published by Occupational Safety Health Administration (OSHA) in United States indicates overload volume level for prolonged listening may harm your hearing. Here below are referenced data on maximum time exposure to sound level before hearing injury occurs.
  • Page 3: Table Of Contents

    4-3 Optional Accessory 9. Important Notice Thank you for choosing the JTS in ear monitoring system. In order to obtain the best efficiency from the system, you are recommended to take a few minutes to read this instruction manual carefully.
  • Page 4: Important Cautions

    8. Audio Input Connector... 2 x Balanced XLR 9. Loop Out Connector....2 x Ø6.3mm Balanced Loop Out Socket Developed with JTS advanced wireless technology. 10.Operation Voltage....12-18 VDC, 300 mA Wired and wireless design for ambience. UHF PLL 16 selectable channels.
  • Page 5: Ie-1

    Parts Identification 3-2 IE-1 4-1 SIEM-2T Front Panel Frequency Response 10 ~ 20,000 Hz 1 Power Switch Transducer Type Dynamic 2 Channel LED Display Impedance 16 Ω 3 Mic.1 / LINE IN Volume Control 4 Mic.2 / LINE IN Volume Control...
  • Page 6: Siem-2R

    4-2 SIEM-2R Rear Panel 1 Antenna 1 DC Input (12V~18V) 2 Power Switch and Volume Control 2 TX Boost 3 Channel Selector 3 Mic.1 / LINE IN LOOP OUT 4 Channel LED Display 4 Mic.2 / LINE IN LOOP OUT 5 6.3mm Mic/ Line In 6 Battery Tray 7 Volume Limiter/Gate ON/ OFF...
  • Page 7: Preparing Procedures

    5 Case 2. Connect the audio source, such as a mixer. Connect the mixer output to the XLR / 6.3mm combo input in the Front panel of SIEM-2T with the AF input 2. Power Suppty cable. NOTE: Two balanced XLR / 6.3mm combo inputs are...
  • Page 8: Siem-2R

    5-2 SIEM-2R 1. Insert and replace batteries 3. Power connection. Connect one end of AC/DC adaptor cable to DC input (1) Slide the lid of battery tray. (Figure 1) (2) Uncover the lid and insert two pieces of 1.5V socket in the rear panel of the receiver, and plug another end into an AC outlet.
  • Page 9: Optional Accessory

    2. Connect with the earphone IE-1 5-3 Optional Accessory (1) Plug the earphone into the jack of the receiver. 1. DR-900/RP-900 Rack Mount Kit (Figure 1) Rack mount kit is available to install the half rack (2) Make sure the volume is at low level to avoid injury transmitter into a standard EIA rack.
  • Page 10: Basic Operation

    Basic Operation 6-1 SIEM-2T 3. Setting LED Display 1. Power On / Off 1 Channel LED Display 2 Channel Selector Turn on or turn off the transmitter by pressing the “POWER” button. Select Channel Hold “Channel Selector” for about 3 seconds, the decimal point in LED Display starts flashing, allowing you to...
  • Page 11: Siem-2R

    6-2 SIEM-2R 1.Power On / Off and Volume 2. Setting LED Display Turn on or off the receiver and adjust the volume by rotating the 1 Channel LED Display volume control clockwise and 2 Channel Selector reversely. NOTE: Please turn off the receiver Select Channel before replacing batteries to ensure Hold “Channel Selector”...
  • Page 12: Installation

    Installation 2.Mix For Multiple Systems Here are some basic operation modes for your reference. This installation enables each performer to create their own mix. Also, you may make use of the loop out connectors for 1. Send the band mix to input (Right / CH.2) of the first multiple systems application.
  • Page 13: Recommendations

    Recommendations Important Notice 1. JTS offers wireless systems in a selection of bands that 1. In order to achieve the optimum reception and also extend the operating distance, please leave an “open space” conform to the different government regulations of specific nations or geographic regions.

This manual is also suitable for:

Siem-2r