Table of Contents
Advertisement
Quick Links
eNet radio transmitter module
eNet radio transmitter module 1-gang
Art. No. : FM..5001M
eNet radio transmitter module 2-gang
Art. No. : FM..5002M
eNet radio transmitter module 3-gang
Art. No. : FM..5003M
eNet radio transmitter module 4-gang
Art. No. : FM..5004M
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Keep button cells out of reach of children! If button cells are swallowed, get medical help
immediately.
Risk of explosion! Do not throw batteries into fire.
Risk of explosion! Do not recharge batteries.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
(1) Base plate
(2) Fastening screws for the base plate
(3) Design frame
(4) Wall transmitter module
(5) Cover
(6) Fastening screws for the wall transmitter module
32595513
J0082595513
Figure 1: 4-gang radio wall transmitter module
1/10
22.03.2017
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Jung FMx5001M Series
Summary of Contents for Jung FMx5001M Series
-
Page 1: Safety Instructions
eNet radio transmitter module eNet radio transmitter module 1-gang Art. No. : FM..5001M eNet radio transmitter module 2-gang Art. No. : FM..5002M eNet radio transmitter module 3-gang Art. No. : FM..5003M eNet radio transmitter module 4-gang Art. No. : FM..5004M Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled... -
Page 2: Operation
eNet radio transmitter module (7) Cover kit (14) Battery holder 3 Function Intended use Radio sensor for transmission of switching, dimming, blind movement and scene commands Operation with radio actuators from the eNet system Product characteristics Display of the actuator status for status poll by a green status LED per channel Display of the transmission status by a red transmission LED Switch-on brightness of dimmer actuators can be saved. - Page 3 eNet radio transmitter module Channel assignment of the wall transmitter Figure 2: Channel assignment of wall transmitter module 1-gang, 2-gang, 3-gang and 4-gang (8) Status LED, green (one per channel) (9) Transmission LED, red (one per device) Operating light Switching: Press button for less than 0.4 seconds. Dimming: Press the button for longer than 0.4 seconds.
- Page 4 eNet radio transmitter module Save switch-on brightness Precondition: The buttons of a channel are set as channel buttons. With dimmer actuators a brightness value can be saved to which the dimmer actuator switches after a short button press. Set required switch-on brightness. Press both buttons of a channel simultaneously for longer than 4 seconds.
- Page 5 eNet radio transmitter module Figure 3: Cutting the adhesive pads for multiple combinations i If necessary, after mounting the wall transmitter in the CD program, carefully remove the excess adhesive film in the corners. 5.2 Commissioning Insert battery WARNING! Risk of chemical burns. Batteries can burst and leak.
- Page 6 eNet radio transmitter module Figure 4: Activating programming mode for channel buttons Press the top left (10) and bottom right (11) buttons simultaneously for longer than 4 seconds (figure 4). The transmission LED (9) flashes slowly. The radio sensor is in programming mode for approx.
- Page 7 eNet radio transmitter module Figure 5: Activating programming mode for scene buttons Press the top right (13) and bottom left (12) buttons simultaneously for 4 seconds (figure 5). The transmission LED (9) flashes slowly. The radio sensor is in programming mode for approx.
-
Page 8: Technical Data
eNet radio transmitter module i The connections in the actuators are preserved and must be deleted separately. Press the top left (10) and bottom right (11) buttons simultaneously for longer than 20 seconds (figure 4). After 4 seconds, the transmission LED (9) flashes. After 20 seconds, the transmission LED flashes faster. -
Page 9: Troubleshooting
eNet radio transmitter module Function Rocker, Other modes, Unused Rocker Basic setting: Rocker The channel works as a channel button. Setting is always made in pairs. Other modes The channel works as a scene button. Setting is always made in pairs. Unused The channel is not displayed in the eNet SMART HOME... -
Page 10: Warranty
Art. No. ..504TSA.. 6.5 Conformity Albrecht Jung GmbH & Co. KG hereby declares that the radio system type Art. No. FM..5001M / FM..5002M / FM..5003M / FM..5004M corresponds to the directive 2014/53/EU. You can find the full article number on the device. The complete text of the EU Declaration of Conformity is available under the Internet address: www.jung.de/ce...
Need help?
Do you have a question about the FMx5001M Series and is the answer not in the manual?
Questions and answers