Mobotix M16 AllroundDual Quick Install

Sensor Module Combinations

M16
2 optical
Day/Night/LPF Day/Night/LPF
• Mx6 system platform, H.264 support
• Recording on internal microSD card (SDXC, SDHC installed)
• Audio integrated (microphone and speaker)
• Sensor for temperature and shock detector(*) integrated
• PIR detector integrated
• Convertible to ceiling installation (ceiling mount included)
• Simply mounted to poles using Pole Mount (accessory)
• Weatherproof and sturdy camera housing(IP66, IK04)
*: with firmware version 5.0.1 and higher

Standard Delivery M16

M.11
M.10
M.9
M.8
M.7
M.6
M.5
M.4
M.3
M.2
M.1
1.19
1.20
1.18
Standard Delivery
Item Count Part Name
Camera housing with mainboard and wall mount (installed), with-
1.1 1
out sensor modules and front element
1.2 1 Front element with additional sensors (installed)
1.3 2 Transport plugs (installed)
Blind module (must be installed when using only one sensor mod-
1.4 1
ule)
1.5 4 Inner housing cover (installed)
Stainless steel Allen screw with flat head M4x8 for inner housing
1.6 4
cover (installed)
Sensor Modules of the M16 (to Be Ordered Separately, Thermal Sensor Pre-Installed)
Sensor module
SMA-S-6D/N/L016
Dome
Plastic nut

Connections and Initial Operation of the M16

You can find detailed information on the installation and connections of the M16 in the M15 Camera Manual (PDF, available on www.mobotix.com >
Support > Manuals).
Please note that the position of the SD card holder has changed (see figure below, at the right), the boot options of this camera have changed compared
to its predecessor (see «Boot Options of the M16» on page 2 ) and the camera only has one key ("L"). Regarding the rest of the initial operation of
the M16, please see the M15 Camera Manual in Chapter 3, «Initial Operation» .
Camera housing
Key L

Preparing the M16 for Installation

To facilitate the installation of the camera, you should complete the following tasks before actually installing the camera.
1. CAUTION!
• Only exchange sensor modules when powered off!
• When operating the camera with only one sensor module, always install
the supplied blind module. No operation with transport plugs!
• Thermal sensor modules are always pre-installed and cannot be removed!

2. Installing the Sensor Modules

Remove the plastic nut from the sensor module
plugs .
2
Push the sensor module cable plug into the connector at the back of the
module housing . Secure the plug using the blue bayonet catch as
3
shown .
4
Insert the sensor module. Make sure that the MOBOTIX lettering on the
sensor module is at the "9 o'clock" position as shown in the figure
Place the back of the black module wrench onto the two holes of the sen-
sor module .
6
Using the black module wrench, turn the sensor module clockwise until
it stops . If desired, insert the two security clips
7
housing as described in «Opening/Closing the Camera Housing» .

Opening/Closing the Camera Housing

The following tasks require opening the camera housing and removing the front element of the M16 in order to get to the interior of the camera:
Inserting the security clips , exchanging the Ethernet patch cable , connecting the USB cable , exchanging the MicroSD card (see also «Inserting/Exchang-
ing the SD Card» on page 2 ).
CAUTION: Make sure the power supply to the camera is disconnected before opening the housing!
1. Opening the Camera Housing
Place the camera face-down on a clean and dry surface. Remove the two
rubber plugs at the back of the camera housing. Using the supplied 5 mm
Allen wrench, loosen the two bolts at the back of the camera housing.
Leave the bolts and washers in the camera housing.
Using the Allen wrench, cautiously
fashion onto the left and the right bolt
out of the front of the housing.
Tilt the front element forward as shown in the figure
2. Inserting the Security Clips
To protect the modules against unwanted removal, insert the two red
security clips at the insides of the sensor modules at the proper location
( inserted, locked). Make sure that the security clips are properly
1 2
locked in their seatings .
3
3. Closing the Camera Housing
Before inserting the front element, make sure that the sensor module cables
of both image sensors are running at the inside of the screw bore
Place the camera on its right side (as seen by the camera) as shown and
insert the front element. When pushing the front element into the housing
( , red arrows), take care not to crush any cables.
2
When inserting and closing the front element, take special care to guide
the cable of the left sensor module under the rubber hook
Press the front element into the camera housing by evenly applying pres-
sure . Tighten the screws with washers.
4
Finally, apply the rubber plugs at the back of the housing that you removed
earlier.
1 optical 1 Thermal/Thermal-TR,
1 optical Day/Night/LPF
1.1
1.4
1.6
1.8
1.12
1.14
1.15
1.17
1.13
1.16
Sensor module
SMA-S-6D/N/L036–237
Protective
glass insert
Plastic nut
Wall Mount
Sensor mod-
ules
PIR sensor
LEDs
Front element
Ethernet patch cable
. Remove the transport
1
. Open the camera
8
push from behind in an alternating
and push the front element
1
.
2
Quick Install
M16 AllroundDual
Modular 6MP Dual Camera with Day/
Night and Thermal Sensor Modules
for Installation on Ceilings or Walls
MOBOTIX 6MP camera for flexible installation in
indoor and outdoor applications, available as M16
AllroundDual with sensor modules SMA-S-6D/N/L016 to
500 with Day/Night or Night-LPF image sensors. Special
"Thermal" model with one Thermal image sensor SMA-
TP-T079/119/237 for thermal imaging and temperature
measurement (-TR) even in complete darkness, optionally
with one additional optical sensor module.
More information:
www.mobotix.com > Products > Outdoor Cameras > M16
Mx-M16
32.845-004_EN_09/2017
Item Count
1.7
1.2
1.8
1.9
1.10
1.3
1.11
1.12
1.5
1.13
1.14
1.7 1.15
1.16
1.9
1.17
1.18
1.19
1.10
1.20
1.11
Item Count
M.1
M.2
M.3
M.4
M.5
M.6
M.7
M.8
M.9
M.10
M.11
Sensor module
SMA-S-6D/N/L500
Lens cover
USB
Sensor mod-
ules
I/O cable to front
element (red clips)
Front element
M16 with two transport
plugs:
No operation allowed!
3
.
5
.
1
3
!
3
Standard Delivery
Part Name
Cable lock black with bayonet catch (Ethernet patch cable, USB, one
2
installed, one supplied)
2 Single wire plug, blue (USB, installed)
1 MicroSD card (SDXC, SDHC pre-installed)
1 Ethernet patch cable, 50 cm/19.7 in with sealing (installed)
2 Sensor module cable 15 cm/6 in (installed in camera)
1 I/O cable with red clips to front element 15 cm/6 in (installed)
1 Hinged ferrite for Ethernet cable (installed)
1 Hinged ferrite for sensor module cable (installed)
2 Rubber plug for covering mounting screws, white
3 Stainless steel Allen screw M6x30 (installed)
3 Stainless steel washer dia. 6.4 mm (installed)
Stainless steel spring washer dia. 6.4 mm (wall/ceiling mount,
1
installed)
1 Stainless steel lock nut M6 (wall/ceiling mount, installed)
1 Rubber plug, black (installed)
Mounting Supplies
Part Name
4 Stainless steel washer dia. 6.4 mm
4 Dowels 8 mm
4 Stainless steel wood screw with hex head 6x50 mm
1 Allen wrench 2.5 mm
1 Allen wrench 5 mm
1 Lens wrench (SMA-S-6D/N/L016 lens, glass/filter insert, dome)
1 Module key (sensor module, focusing of lenses)
1 Rubber sealing for wall/ceiling mount, white
1 Ceiling mount for VarioFlex mount
4 Protection cover for screw, white
4 Security clip for sensor or blind modules, red
(all except Thermal)
Top (markings)
Sensor module R USB
Ethernet
Slot for microSD card
M16 with one transport
plug:
No operation allowed!
2
1
5
7
1
1
2
3
1
Rear
Sensor module cable
Sensor module L
M16 with one blind module:
Unrestricted operation
(IP66)
4
6
8
2
2
4