Heat & Glo SL-3X Owner's Manual page 24

Adjusting Flame Height
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the FLAME
icon and press SELECT.
• Use the UP and DOWN arrows to adjust the FLAME
HEIGHT, then press SELECT. The FLAME HEIGHT
can be adjusted to 5 different settings.
NOTICE: FLAME HEIGHT will not be adjustable for  rst
ten seconds when  replace is turned on.
NOTICE: The system will remember the previous FLAME
HEIGHT setting and will automatically adjust after 10
seconds.
Adjusting Fan Speed
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the FAN icon
and press SELECT.
• Use the UP and DOWN arrows to adjust the FAN SPEED,
then press SELECT. The FAN SPEED can be adjusted
to 3 different settings: HIGH, MEDIUM, LOW.
NOTICE: The fan is controlled by a timer built into the
control module. After the  replace is turned ON the timer
will wait for 3 minutes before turning on the fan. In addition,
the fan will remain on for 12 minutes after the  replace has
been turned OFF.
NOTICE: The FAN will start up on the high setting for 10
seconds before adjusting to the previous user setting.
AUX1 Function (Unit dependent Function)
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the AUX1 icon
and press SELECT.
• Use the UP and DOWN arrows to adjust the AUX1 output,
then press SELECT. The AUX1 function can be adjusted
to 4 different settings: HI, MED, LOW and OFF.
AUX2 Function (Unit dependent Function)
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the AUX2 icon
and press SELECT.
• Use the UP and DOWN arrows to turn the AUX2 ON or
OFF, then press SELECT. The AUX2 function can be
either be turned ON or OFF.
NOTICE: The system will remember the previous AUX1
and AUX2 setting from the menu. However, when the  re-
place is turned OFF both AUX1 and AUX2 will be turned
off. AUX1 and AUX2 can be activated when the  ame is off
from the remote's OFF mode. When the  replace is turned
back ON the AUX1 and AUX2 settings will be restored to
the previous ON setting.
Please contact your Hearth & Home Technologies dealer with any questions or concerns.
2 Hearth & Home Technologies • RC300 Multifunction Remote Control Operating Instructions • 2166-396 Rev. D • 5/15
30
For the location of your nearest Hearth & Home Technologies dealer,
please visit www.hearthnhome.com.
Heat & Glo • SL-3X, SL-5X, SL-7X, SL-9X Owner's Manual • 2372-981 Rev. F • 7/17
Adjusting Thermostat
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the THERMO
icon and press SELECT.
• Use the UP and DOWN arrows to turn the THERMO ON
or OFF, then press SELECT (the SET TEMP will start
blinking). Using the UP and DOWN arrows select the
desired temperature and press SELECT.
NOTICE: If the THERMO function is on, the SET TEMP
can be adjusted at any time by pressing the UP and DOWN
arrows.
NOTICE: As the ROOM TEMP (RT) approaches SET
TEMP (ST), the remote system will automatically adjust
the  ame height. If the RT rises above ST, the  replace
will shut down the main burner. After this, the  replace will
turn back on after the RT drops below the ST.
NOTICE: The system requires a two degree Fahrenheit
or higher temperature difference between RT and ST for
the  replace to turn on.
NOTICE: The system will remember the previous TEM-
PERATURE setting when THERMOSTAT mode is cycled
ON or OFF.
Adjusting Timer
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the TIMER
icon and press SELECT.
• Use the UP and DOWN arrows to turn the TIMER ON
or OFF, then press SELECT. Using the UP and DOWN
arrows select the desired set time and press SELECT.
Timer operates in increments of 15, 30, 45, 60, 90, 120
and 180 minutes.
Activating/Deactivating Constant Pilot
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the PILOT
icon and press SELECT.
• Use the UP and DOWN arrows to turn the CONSTANT
PILOT ON or OFF, then press SELECT.
NOTICE: A beep will come from the control module
indicating CONSTANT PILOT has been activated. A
double beep will come from the control module indicating
CONSTANT PILOT has been deactivated.
Setting the Child Lock
• Press and hold the MENU and UP arrow buttons simul-
taneously for 4 seconds to enable or disable the child
lock feature.
NOTICE: No functions will be usable until child lock feature
is disabled.