Table of Contents
Advertisement
Quick Links
LIST OF PRODUCTS
Digital Multimeter
Digital AC & AC/DC Clampmeter
AC Clamp Adaptor
AC/DC Current Adaptor
Thermo Anemometer
Thermo Hygrometer
Distance Meter
Digital Lux Meter
Network Cable Tester
Power Factor Regulator
Earth Resistance Tester
Digital Panel Meters
DC Power Supplies
High Voltage Detector
Calibrators
Gas Analysers
Frequency Counter
Function Generator
Phasing Sticks
Battery Tester
Waterproof Pen Testers
Solar Power Meter
EMF Detector
Wood, Paper & Grain Moisture Meter
Transistorised Electronic Analog & Digital Insulation
Resistance Testers(upto 10 KV)
Digital Sound Level Meter & Sound Level Calibrator
Digital contact & Non-contact Type Tachometer
Digital Non-contact (infrared) Thermometer
Maximum Demand Controller/Digital Power Meter
Digital Hand Held Temperature Indicators
G 17, Bharat Industrial Estate, T. J. Road,
Sewree (W), Mumbai - 400 015. INDIA.
Sales Direct : (022) 24156638
Tel. : (022) 24124540, 24181649. Fax : (022) 24149659
Email : kusam_meco@vsnl.net
Website : www.kusamelectrical.com
www.kusam-meco.co.in
®
AN ISO 9001:2015 COMPANY
AC TRUE RMS
DIGITAL CLAMPMETER WITH
EF-DETECTION, AMPTIP FUNCTION
FOR LOW CURRENT
MEASUREMENT
MODEL - KM 033
OPERATION MANUAL
® ®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kusam-meco KM 033
Summary of Contents for Kusam-meco KM 033
- Page 1 Digital Non-contact (infrared) Thermometer Maximum Demand Controller/Digital Power Meter Digital Hand Held Temperature Indicators ® MODEL - KM 033 G 17, Bharat Industrial Estate, T. J. Road, Sewree (W), Mumbai - 400 015. INDIA. Sales Direct : (022) 24156638 Tel.
-
Page 2: Terms In This Manual
DIGITAL CLAMPMETER No. 61010-1Ed.3.0, UL/IEC/EN61010-2-032 Ed.3.0, UL/IEC/ EN61010-2-033 Ed. 1.0 to measurement CAT-III 600V and MODEL - KM 033 CAT-IV 300V, AC & DC. The accompanied test probe assembly meets UL/IEC/EN61010- 031 Ed. 2.0 to the same meter ratings or better. IEC 61010-031 requires exposed conductive test probe tips to be ≤... -
Page 3: International Electrical Symbols
® ® Keep your hands/fingers behind the hand/finger barriers (of the MEASUREMENT CATEGORY III is applicable to test & measuring meter and the test leads where applicable) that indicate the limits of circuits connected to the distribution part of the building’s low-voltage safe access of the hand-held part during measurement. -
Page 4: General Specifications
® ® SAFETY : GENERAL SPECIFICATIONS : Safety : Certified per IEC/UL/CSA_C22.2_# / EN standards. 61010-1 Ed.3.0, Sensing : True RMS 61010-2-032 Ed. 3.0,61010-2 033 Ed. 1.0 & 61010-031 Ed. 2.0 to Jaws Opening size : 26mm Max. Measurement Categories CAT III 600V AND CAT IV 300V AC &... -
Page 5: Electrical Specifications
® ® DC VOLTAGE ELECTRICAL SPECIFICATIONS : Range Accuracy Resolution Accuracy is ± (% of reading digits + number of digits) or otherwise ±(1.0%rdg + 5dgts) 600.0 V specified, at 23 C ± 5 C. Maximum Crest Factor <2 :1 at full scale & Input Impedance : 10M, 100pF nominal <4:1 at half scale or otherwise specified, and with frequency spectrum not exceeding the specified frequency bandwidth for non-sinusoidal... - Page 6 ® ® CAPACITANCE BeepLit CONTINUITY TESTER Range Resolution Accuracy Continuity Threshold Between 30 & 480 200.0 F 0.1 F Continuity ON ±(2.0%rdg + 4dgts) 15ms approx. Response Time 2500 F F Audible Indication Beep sound Accuracies with film capacitor or better Visible Indication LCD Backlight HZ LINE LEVEL FREQUENCY...
-
Page 7: Product Description
® ® VII. OPERATION : VI. PRODUCT DESCRIPTION : WARNING : Before and after hazardous voltage measurements, test the voltage function on a known source such as line voltage to This manual uses only representative model(s) for illustrations. determine proper meter functioning. Please refer specification details for function availability to this model. - Page 8 ® ® Clamp-on Current Measurements : Clamp-on AmpTip ACA Application & Removal of the Jaws Input is made via the clamp jaws where Press the jaw trigger & clamp the jaws around conductor(s) of only best accuracy is specified near the jaw one single pole of a circuit for load current measurements.
- Page 9 ® ® Resistance, BeepLit Continuity & BeepLit Diode : CAUTION : Using Resistance, BeepLit Continuity or BeepLit Diode function in Inputs are made through the test lead terminals COM/+. a live circuit will produce false results and may damage the meter. In Defaults at ...
- Page 10 ® ® Probe-Contact EF-Detection : For more precise indication of live DCA Current function : wires, such as distinguishing between Live and Ground connections, Inputs are made through the test lead terminals COM/+. Defaults at use one single probe to test via terminal COM for direct metal EF-Detection function.
-
Page 11: Record Mode
® ® Capacitance & Temperature : CAUTION : Inputs are made through the test lead terminals COM/+. Defaults at Discharge capacitors before making capacitance measurements. Large Capacitance. Press SELECT button momentarily to select °C value capacitors should be discharged through an appropriate resistance load. -
Page 12: Power-On Option
® ® V. MAINTENANCE : Intelligent Auto-Power-Off (APO) : WARNING : The Auto-Power-Off (APO) mode turns the meter off automatically to To avoid electrical shock, disconnect the meter from any circuit, extend battery life after approximately 32 minutes of no specified remove the test leads from the input jacks and turn OFF the meter activities, where applicable, below : before opening the case. -
Page 13: Test Certificate
® WARRANTY MUMBAI Each “KUSAM-MECO” product is warranted to be free from defects in TEST CERTIFICATE material and workmanship under normal use & service. The warranty period is one year (12 months) and begins from the date of despatch of goods.
Need help?
Do you have a question about the KM 033 and is the answer not in the manual?
Questions and answers