Related Manuals for Clarke HSEC651A
Summary of Contents for Clarke HSEC651A
- Page 1 SUBMERSIBLE SEWAGE CUTTER PUMP MODEL NO: HSEC650A/651A/1400A PART NO: 7230290, 7230295, 7230243 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS LS0218 ISS 1...
-
Page 2: Environmental Recycling Policy
INTRODUCTION Thank you for purchasing this CLARKE Submersible Sewage Cutter Pump. The pump is fitted with a tungsten carbide cutter, and is especially suited for heavily polluted water containing waste solids, such as sewage, light slurry etc. This pump is NOT designed for pumping heavy slurry, sludge, mud, salt water, or any water containing chemicals or other acidic contaminants. -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS GENERAL PUMP SPECIFIC 1. Read all instructions before use 1. Do not pump explosive / and save these instructions for flammable liquids or chemicals. future use. 2. Never allow the pump to run dry 2. An approved residual current or operate out of the water. -
Page 4: Electrical Connections
GREEN wire must be connected to the terminal which is marked E or or coloured green. HSEC651A must be connected to a protected 110V supply, through a suitably approved connector. On no account must a 230V, 13amp plug be used. -
Page 5: Using The Pump
1. Using the adaptor if required, connect a suitable hose (not supplied) to the pump outlet. • Suitable hoses are available from your local Clarke dealer. 2. Place the pump vertically on a flat surface in the area that you want to drain. - Page 6 • You can adjust the position at which the float switch lead is held to the pump. Adjusting the length of the float switch lead will change the depth of water at which the pump will turn on or off. 5.
-
Page 7: Maintenance
IS UNPLUGGED FROM THE MAINS SUPPLY. IF THE UNIT IS HARD WIRED, ENSURE THE CIRCUIT BREAKER IS OPEN. This pump should require no maintenance other than regular cleaning. If the pump starts to show signs of wear or damage, contact your CLARKE dealer for advice. CLEANING 1. -
Page 8: Troubleshooting
7. Water level too low - float switch in OFF position - lift float to check switch. 8. If the pump still fails to start, consult your CLARKE dealer for advice. PUMP WILL 1. Check that the inlet is not blocked. -
Page 9: Parts Diagram Hsec1400A
PARTS DIAGRAM HSEC1400A Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 10: Parts List Hsec1400A
PARTS LIST HSEC1400A Motor Cover O-ring (Oil Hole) Motor Housing Gasket (Leak Test Hole) Rotor Gasket (Flange) Stator (240V/50HZ) Gasket (Cable) Bearing Cover Flange Oil Seal Cover Hose tail Pump Housing Handle Cutter Impeller (50HZ) Float Switch Strainer Power Cable Set Capacitor Cable Clamp Upper Bearing... - Page 11 PARTS DIAGRAM HSEC650A/651A Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 12 PARTS LIST HSEC650A/651A HSEC650A HSEC651A DESCRIPTION HG650A01 HG651A01 Upper Cover HG650A02 HG651A02 Top Bearing Cover HG650A03 HG651A03 Motor Housing HG650A04 HG651A04 Stator HG650A05 HG651A05 Rotor HG650A06 HG651A06 Seal Cover HG650A07 HG651A07 Seal Plate HG650A08 HG651A08 Impeller HG650A09 HG651A09 Pump Casing...
-
Page 13: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 14 DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 15 DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the HSEC651A and is the answer not in the manual?
Questions and answers