Table Of Contents; Specific Safety Notes; General View (Fig. 1); Description Of Machine - Proxxon KGS 80 Manual

Translation of the Original Operating Instructions
G
KGS 80 Crosscut and mitre saw
Contents:
1 Specific safety notes................................................10
2 General view (fig. 1) ................................................10
3 Description of machine ............................................10
4 Technical data ..........................................................11
5 Before beginning work ............................................11
6 Working with the KGS 80 Crosscut
and mitre saw ..........................................................11
6.1 Cutting capacity ......................................................11
6.2 Sawing ......................................................................12
6.2.1 General notes on setting the saw head ..................12
6.2.2 Straight and mitre cuts ............................................12
Dear Customer!
Using these instructions
• makes it easier to get familiar with the device
• prevents malfunctions caused by improper handling, and
• engthens the service life of your device.
Please keep these instructions readily accessible at all times.
Use the device only when you have understood it exactly and always
adhere to the instructions.
PROXXON is not liable for the safe functioning of the device in cases
of:
• handling that does not conform to the usual usage,
• purposes of use not designated in the instructions,
• disregard of the safety instructions.
You are not entitled to guarantee claims in cases of:
• operator errors,
• inadequate maintenance.
For your own safety, please follow the safety instructions exactly.
Use only genuine PROXXON replacement parts.
We reserve the right to make improvements in the sense of techni-
cal progress. We wish you much success with the device.
WARNING!
Read all safety warnings and instructions. Failure to
follow all safety warnings and instructions listed below
may result in electric shock, fire and/or serious injury.
KEEP ALL SAFETY WARNINGS AND INSTRUCTIONS FOR THE
FUTURE !

1 Specific safety notes

Caution!
Damaged or deformed saw blades may not be used.
Use only saw blades recommended by the manufacturer and which
correspond to EN 847.
Use only saw blades that have been properly sharpened. Comply with
the maximum rotational speed specified on the saw blade.
- 10 -
6.2.2.1 If you would like to produce straight cuts
(see fig. 2a) ..............................................................12
6.2.2.2 If you would like to produce mitre cuts:
(See fig. 2b): ............................................................12
6.2.3 Working with the Length Stop (see fig. 4) ..............12
7 Care and Maintenance ............................................13
7.1 Replacing the saw blade
(see fig. 5a and 5b):..................................................13
7.2 Cleaning....................................................................13
8 Disposal ....................................................................13
9 EC Declaration of Conformity ..................................13
Please remember that there are several rules that reduce the noise
development of the machine:
Always select the correct saw blade for your work task! Of particu-
lar importance is that the blade is suitable for the material to be
sawn.
Clamp the work pieces to be sawn as short as possible! If a work
piece projects too far out of the vice, it can vibrate and cause noise.
Use the saw head adjustment to set the distance as described in the
chapter "General notes on setting the saw head".

2 General view (fig. 1)

1. Saw head
2. Saw blade cover
3. Locking lever
4. Saw blade
5. Device base
6. Clamping screw
7. Turntable
8. Spindle for clamping fixture
9. Limit stop
10. Clamping fixture
11. Scale
12. Fastening bores
13. Adjusting screw for saw head

3 Description of machine

Thank you for purchasing the PROXXON KGS 80 Crosscut and mitre
saw.
The saw is not only excellently suited for small yet fine applications
for separating wood, non-ferrous metals and plastics, but also larger
round and square materials can be easily cut in two no matter whether
with a straight cut or with a precise and freely adjustable mitre.
The work piece is clamped in the integrated vice for sawing and
separating. The centrically clamped jaws ensure that the imaginary
centre line of the vice opening - therefore the centre of the work
piece - will always "hit" the centre of the saw blade independent of
the selected work piece width.