Standard Pump SP-CPVC Operating Instructions Manual

Standard Pump Operating Instructions and Parts Manual (
Standard Pump
Industrial Drum Pump Models:
SP-PP, SP-PHT, SP-CPVC, SP-AL, SP-PVDF & SP-SS
Description
Standard's Drum Pumps are designed to
transfer a variety of materials from 55 gallon
drums and tanks. Standard Pump offers
several different pumps, each designed
for specific applications. Before operating,
please confirm that the pump's materials of
construction are suitable for the application.
Unpacking
Cartons should be handled with care to avoid
damage from dropping, etc. After unpacking,
inspect carefully for any damage that may
have occurred during transit. Check for loose,
damaged or missing parts.
General Safety Information
The responsibility for safe assembly,
installation, and operation ultimately rests
with the operator. Read and understand ALL
safety precautions and operating instructions
before operation. Careless pump operation
can result in serious injury.
Before operating the pump, read and
1.
understand these operating instructions.
2. The operator should wear suitable
protective clothing including the
following: face mask, safety shield or
goggles, gloves, apron, and safety
shoes.
Before operating, verify the materials
3.
being pumped are compatible with the
pump's "wetted components."
All Federal, State, and local safety codes
4.
should be followed.
Drum Pump Specifications
Material of
Model
Construction
SP-CPVC CPVC
SP-CPVC-HH CPVC
SP-PP Polypropylene
SP-PP-HH Polypropylene
SP-PHT Polypropylene
SP-PHT-HH
Polypropylene
SP-PVDF
PVDF (Kynar
SP-PVDF-HH
PVDF (Kynar
*SP-SS
SS316
*SP-SS-HH
SS316
*SP-AL
Aluminum
*SP-AL-HH
Aluminum
* When operating in Hazardous Duty applications a pump must be used in conjunction with an explosion proof motor or air motor.
OIPM-IND-0713
Verify that the motor voltage
5.
corresponds to proper electrical supply.
6. Before plugging motor into power
supply, make sure the motor switch is in
the OFF position. For Air Motors ensure
inlet valve is closed before attaching air
line.
Before operation, confirm all pump
7.
connections are properly tightened.
First pump clean water in order to
8.
familiarize yourself with the pump's
operation, flow rate, discharge pressure
and motor speed.
Before starting the pump, confirm the
9.
discharge hose is securely fastened to
the receiving vessel in order to prevent
splashing.
Never leave pump unattended during
10.
operation.
Do not submerge the motor in any liquid.
11.
When finished using the pump, flush
12.
the pump by pumping water or an
appropriate cleaning solution. Do not
use flammable or combustible cleaning
solutions.
Never carry the motor by the power
13.
cord.
14. Never store pump in container. Always
rinse pump thoroughly and hang on wall
bracket or ensure pump tube is stored in
an upright and vertical position.
combustible products or operating in a
Maximum Liquid
Temperature
190º F (90º C)
190º F (90º C)
130º F (55º C)
130º F (55º C)
175º F (80º C)
175º F (80º C)
) 175º F (80º C)
®
) 175º F (80º C)
®
175º F (80º C)
175º F (80º C)
175º F (80º C)
175º F (80º C)
)
When pumping
flammable or
Wetted Materials
CPVC, Carbon, Hastelloy C, PVDF, PTFE
CPVC, Carbon, Hastelloy C, PVDF, PTFE
PP, Carbon, Hastelloy C, PTFE
PP, Carbon, Hastelloy C, PTFE
PP, Carbon, Hastelloy C, PTFE
PP, Carbon, Hastelloy C, PTFE
PVDF, Carbon, Hastelloy C, PTFE
PVDF, Carbon, Hastelloy C, PTFE
SS316, Carbon, PTFE
SS316, Carbon, PTFE
Aluminum, Carbon, PTFE & SS316
Aluminum, Carbon, PTFE & SS316
1
hazardous duty environment, the SP-AL
or SP-SS Series pump must be used in
conjunction with an explosion proof
motor. Please contact the factory or an
authorized distributor with any questions
regarding this matter.
Assembly
Remove the pump and motor from
1.
packaging.
Inspect all contents for damage.
2.
3. Couple the motor to the pump tube by
using the Hand Wheel. (See figure 1).
Figure 1
Maximum Flow Rate
35 gpm (132 l/min) 16 psi (1,1 bar)
16 gpm (60 l/min) 32 psi (2,2 bar)
35 gpm (132 l/min) 16 psi (1,1 bar)
16 gpm (60 l/min) 32 psi (2,2 bar)
35 gpm (132 l/min) 16 psi (1,1 bar)
16 gpm (60 l/min) 32 psi (2,2 bar)
35 gpm (132 l/min) 16 psi (1,1 bar)
16 gpm (60 l/min) 32 psi (2,2 bar)
35 gpm (132 l/min) 16 psi (1,1 bar)
16 gpm (60 l/min) 32 psi (2,2 bar)
35 gpm (132 l/min) 16 psi (1,1 bar)
16 gpm (60 l/min) 32 psi (2,2 bar)
Discharge
Pressure