Improper Use; Technical Description; Safety Instructions; Identification Of Safety Instructions - WALTHER PILOT wa110 Operating Instructions Manual

must be consulted.
Grounding / Equipotential Bonding
You must ensure that the spray gun is properly earthed (grounded) either separately
or in connection with the equipment with which it is being used (maximum resistance
10 Ω).
6
1.3

Improper Use

This spray gun shall not be used for purposes other than set forth in the above
Chapter Normal Use. Any other form of use and/or application is prohibited.
Improper use is for example:
• spraying of material onto persons and animals
• spraying of liquid nitrogen, etc.
2

Technical Description

The automatic spray gun PILOT WA 110 works with compressed air control. The
atomizer air is controlled via an externally arranged pressure reducing valve. The
gun body is made of 1.4305.
3

Safety instructions

3.1

Identification of safety instructions

Warning
The pictogram and the urgency level "Warning" identify a possible danger to
persons. Possible consequences: Slight to severe injuries.
Caution
The pictogram and the urgency level "Caution" identify a possible danger to mate-
rial assets. Possible consequences: Damage to material assets.
Note
The pictogram and the urgency level "Note" identify additional information for the
safe and efficient operation of the spray gun.
3.2

General Safety Instructions

• All applicable accident prevention rules and regulations as well as other recognised
industrial safety and health rules and regulations must be observed at all times.
• Use the spray gun only in well-ventilated rooms. Fire, naked flames and smoking are
strictly prohibited within the working area. WARNING – during the spraying of flammab-
le materials (e.g. lacquers, adhesives, cleaning agents, etc.), there is an increased risk
to health as well as an increased risk of explosion and fire.
• Measures must be taken to ensure that the spray gun is sufficiently grounded (earthed)
by means of a conductive air hose (maximum resistance 10
• Before carrying out maintenance or servicing work, always ensure that the air and
material feed to the spray gun have been de-pressurised. Risk of injury!
• When spraying materials, do not place your hands or other parts of the body in front of
the pressurised nozzle or the spray gun. Risk of injury!
• Never point the spray gun at persons or animals. Risk of injury!
Ω).
6
18
• Always observe the spraying and safety instructions given by the manufacturers of the
spraying material and the cleaning agent. Aggressive and corrosive materials in
particular can be harmful to health.
• Exhaust air containing particles (overspray) must be kept away from the working area
and personnel. In spite of these measures, always wear the regulation breathing masks
and protective overalls when using the gun. Airborne particles represent a serious
health hazard!
• Always wear hearing protection when using the gun or when in the vicinity of a gun that
is in use. The noise level generated by the spray gun is approx. 83 dB (A).
• After carrying out assembly or maintenance work, always ensure that all nuts, bolts and
screw connections have been fully tightened before the gun is used.
• Use only original replacement parts, since WALTHER can only guarantee safe and
fault-free operation for original parts.
• For further information on the safe use of the spray gun and the spraying materials,
please contact WALTHER Spritz- und Lackiersysteme GmbH, D-42327 Wuppertal,
Germany.
4

Assembly

The spray gun is delivered fully assembled. Before using it, the following steps
should be carried out:
4.1 Mounting of Spray Gun
Install the gun in a suitable and stable mounting device.
4.2

Connection of Input Lines

Warning
Make sure not to confuse the control and atomizing air connections -risk of injury.
Warning
Material and air hoses which are installed with a hose grommet must be additionally
secured with a hose clamp.
Materialconnection
Control air connection
Atomizer air connection
The spray gun is now properly installed and ready for operation.
5

Starting / Handling

The following requirements must be met before the spray gun is operated:
• The control air pressure must be available at the gun
19