Table of Contents
Advertisement
Pos: 3 1.13 / Übers chrifte n/1. 1/Trans port- und Verpa ckungsmaterial @ 1 8\ mod_ 1122 5445 39707 _18.docx @ 1 9774 3 @ 2 @ 1
5.2
Transport and packaging material
Pos: 3 1.14 /I nbetriebnahme - M ontage/Ter motek/Te xt - Da s Gerät wird auf ei ner Sonderpalette angelie fert. @ 15 6\mod_ 13720 6736 2377_ 18.docx @ 1 58754 3 @ @ 1
Pos: 3 1.15 /I nbetriebnahme - M ontage/Transport von GerätenTransport- und Verpack ungs material entfer nen. @ 15\ mod_110 62346 1109 7_18. docx @ 1324 56 @ @ 1
Pos: 3 1.16 /I nbetriebnahme - M ontage/Transport von GerätenTransport- und Verpack ungs material entsorge n @ 81\ mod_1 26779 2765 671_1 8.docx @ 891 391 @ @ 1
Pos: 3 1.17 /Hi nweise/Allge meinHi nweis - G erät nach A uspa cken auf Trans ports chäde n ... pr üfe n. @ 18 1\mod_ 1389 35979 4718_ 18.docx @ 1 84028 4 @ @ 1
Pos: 3 1.18 /Hi nweise/Allge meinHi nweis - Tra nsportbes chädig ungen bei eventuelle n Rücktransport @ 190 \mod_1 3966 09731 059_ 18.docx @ 19 0490 9 @ @ 1
Pos: 3 1.19 / Übers chrifte n/1. 1/Erstinbetriebna hme @ 156\ mod_13 7223 50610 91_1 8.docx @ 158 9365 @ 2 @ 1
5.3
Start-up
Pos: 3 1.20 /Hi nweise/Elektro (Ge fahr, War nung, Vor sicht )Ge fahr - E -Ans chlüsse - Arbeiten am ge öffnete n Gehä use @ 190\ mod_13 96004 0470 08_18 .docx @ 189 7564 @ @ 1
Pos: 3 1.21 /I nbetriebnahme - M ontage/Ter motek/SH X30Erstinbetriebna hme @ 242 \mod_ 14229 5900 8583_ 18.docx @ 22 3552 0 @ @ 1
Pos: 3 1.22 / -- leer --/ ====== == @ 1\ mod26_ 18.docx @ 2 7188 @ @ 1
Setting Up
The unit will be delivered on a special pallet.
Remove any transport material and packaging.
Dispose of the transport and packaging material in an environmentally-compliant manner
and in accordance with the applicable local rules and regulations.
Note
After unpacking, check the unit for signs of transport damage or other damage.
Note
In order to avoid transport damage if the unit needs to be returned to the manufacturer,
return the unit solely in its original packaging.
DANGER
Electrical hazard!
It may be necessary to open the housing in order to perform work on the unit. Exposed
parts may be energised and cause an electric shock if they are touched.
Observe the following points when working on the electrical system:
•
Observe the "Safety" section.
•
Ensure that the tasks are performed solely by qualified experts.
1.
Disconnect the unit from the power supply in order to deenergise it.
2.
Secure the unit so that it cannot be switched on again accidentally.
3.
Check whether the unit is properly disconnected from power and absolutely
voltage-free
4.
Earth and short-circuit the unit.
5.
Cover any adjacent live parts and secure the danger area.
Prior to the start-up, the following tasks must be performed:
•
Set the unit up.
•
Connect the cooling water supply.
•
Connect the power supply.
•
Vent the unit.
Note
The set-up, start-up, maintenance, and service should be performed by the after-sales
service. If necessary, contact the after-sales service (see the "Contact addresses" section).
VARISTAR Cooling unit SHX 30
34
Advertisement
Table of Contents
