Dhollandia DH-LSP Series DH-LSP.05 Operation Manual
  1. Manuals
  2. Brands
  3. Dhollandia Manuals
  4. Lifting Systems
  5. DH-LSP SeriesDH-LSP.05
  6. Operation manual

Dhollandia DH-LSP Series DH-LSP.05 Operation Manual

Van tail lifts
Hide thumbs
Table of Contents

Advertisement

Quick Links

use-DHLSP-CE en-2017-A-01
28/08/2018
DH-LSP* van tail lifts
OPERATION MANUAL
Manufacturer:
DHOLLANDIA N.V.
Zoomstraat 9
9160 LOKEREN (Belgium)
Tel : +32 (0)9 349 06 92
Fax : +32 (0)9 349 09 77
e-mail : info@dhollandia.be
website : www.dhollandia.com
Read the manual in its entirety before operating the tail lift.
Keep this manual in the vehicle cab, as reference for the driver and tail lift operator

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DH-LSP Series DH-LSP.05 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dhollandia DH-LSP Series DH-LSP.05

Summary of Contents for Dhollandia DH-LSP Series DH-LSP.05

  • Page 1 9160 LOKEREN (Belgium) Tel : +32 (0)9 349 06 92 Fax : +32 (0)9 349 09 77 e-mail : info@dhollandia.be website : www.dhollandia.com Read the manual in its entirety before operating the tail lift. Keep this manual in the vehicle cab, as reference for the driver and tail lift operator...

  • Page 2: Table Of Contents

    Switching the main power on/off ............................35 Operation of the standard platform ............................36 Operation of the LSPZ platform............................40 The use of cart-stops ................................44 DECALS....................................... 46 10.1 Regular decals ..................................46 MEANING OF SAFETY AND WARNING SIGNS ........................49 END NOTE ....................................51 DHOLLANDIA...

  • Page 3: Understanding Safety And Warning Signs

    Prior to operating the tail lift, make sure you understand the safety and warning signs used, and read them in conjunction with • the instructions in this manual. If in doubt, DO NOT operate the tail lift. Contact your national DHOLLANDIA distributor. See page 3 for contact info. • DHOLLANDIA...

  • Page 4: Contact Information And Disclaimers

    Contact your national DHOLLANDIA distributor if you have any questions regarding the installation, operation, repair and maintenance of DHOLLANDIA tail lifts, to obtain replacement copies of manuals or decals, or to learn about available equipment options for DHOLLANDIA tail lifts.

  • Page 5: General Introduction

    4 INTENDED USE DHOLLANDIA tail lifts are designed to be fitted to commercial vehicles (commercial trucks, trailers and semi-trailers), and shall be used exclusively to load and unload the goods transported on the vehicle it is fitted to, within the limits of the load chart, in compliance with the operator instructions and safety instructions described in this manual.

  • Page 6: Identification

    6 DESCRIPTION AND TAIL LIFT TERMINOLOGY GENERAL DHOLLANDIA tail lifts are developed and manufactured using state-of-the-art technology, high quality materials and components, • and highly skilled workmanship. They comply with the European CE safety regulations mentioned in the Declaration of Conformity issued with each lift (unless agreed otherwise for tail lifts exported outside of CE region).
  • Page 7 Center point of maximum load : point up to which the maximum rated capacity of the tail lift is valid. Beyond that point, the maximum safe working load diminishes according to the applicable load charts found at Section 8 of this manual. DHOLLANDIA...
  • Page 8 Bottom view DHOLLANDIA...
  • Page 9 Center point of maximum load : point up to which the maximum rated capacity of the tail lift is valid. Beyond that point, the maximum safe working load diminishes according to the applicable load charts found at Section 8 of this manual. DHOLLANDIA...
  • Page 10 Bottom view DHOLLANDIA...

  • Page 11: Safety Devices

    SAFETY DEVICES DHOLLANDIA tail lifts are equipped with a multiple safety devices in order to ensure that goods can be loaded and unloaded with maximum safety for the operator, any potential bystanders, and the load itself. The following safety devices are incorporated or recommended on most tail lifts: Electrical safety valves mounted on all cylinders [standard].
  • Page 12 Fuses [standard]. A 15A fuse for the electrical control circuit is premounted in the pump unit and in the exterior control box (for • most types). A 150 - 250A fuse for the electrical main battery circuit is supplied by the truck manufacturer or by DHOLLANDIA. Both fuses protect the electrical circuits against short-circuits and amperage peaks.
  • Page 13 5. A combination of 2 or more of the above. The various means above have variable efficiency depending on the direction of approach and the light conditions (e.g. bright sunlight versus night darkness). DHOLLANDIA strongly recommends a combination of 2 or 3 means to cover all circumstances.

  • Page 14: Safety Instructions For Using The Tail Lift

    7 SAFETY INSTRUCTIONS FOR USING THE TAIL LIFT DO NOT USE TAIL LIFT WITHOUT ADEQUATE SAFETY AND OPERATOR TRAINING DHOLLANDIA tail lifts shall be exclusively used to load and unload the goods transported on the carrying vehicle, within the limits •...
  • Page 15 NOTICE DHOLLANDIA offers optional platform mounted flashing lights and flags to make the platform more visible to other people. Please visit www.dhollandia.com or contact the national DHOLLANDIA distributor for more information. See page 3 for contact info.
  • Page 16 Inspect the tail lift prior to each use. If any unsafe condition exists or unusual noises or movements are noticed, DO NOT use • the tail lift and contact an authorized DHOLLANDIA service agent for repair. Please see ‘pre-trip inspection’ procedures under 7.6 page 22.
  • Page 17 ALWAYS be sure to clearly identify to other drivers that the tail lift is in use. Dhollandia recommends use of warning cones to clearly identify to drivers that the tail lift is being operated.
  • Page 18 The most important safety and operation instructions are summarized in a product video • that can be viewed online at For LSP http://www.dhollandia.com/uservideo/LSP-CE-2018-01 For LSPZ foldable http://www.dhollandia.com/uservideo/LSPZ-CE-2018-01 Make sure you review these instructions prior to operation of the associated DHOLLANDIA tail lift. DHOLLANDIA...

  • Page 19: Danger Zones, Risk Of Crush And Shear Injury

    ALWAYS stand clear of the range of motion of the platform and moving parts of the tail lift; o Keep hands, feet and upper body clear of pinch points and moving parts of the tail lift; o DO NOT allow any other person to stand near the tail lift and its platform. DHOLLANDIA...

  • Page 20: Safe Operator Position

    Consult the latest edition of DHOLLANDIA’s fitting instructions FIT-ELEC-OPTION or contact your national DHOLLANDIA dealer for more information. See page 4 for contact info.
  • Page 21 It is prohibited to bypass or modify any of the safety features of the tail lift. If connection of the power to the external control box • does not deactivate external controls, stop using the tail lift, and contact an authorized DHOLLANDIA agent. WARNING When standing in front or behind the load, the operator risks being pushed off the platform, or being crushed between the •...

  • Page 22: Instructions For Working At Loading Docks

    Ensure there 150mm. is sufficient clearance under and above the platform, taking into account all anticipated position shifts of the vehicle suspension. Make sure the platform does not touch the ceiling, ground or end wall of the storage pocket. DHOLLANDIA...

  • Page 23: Recommended Daily Pre-Trip Inspection

    To avoid this risk, inspect the tail lift prior to the first use of each day. Ensure that all safety systems and all functions operate • correctly, and that no maintenance or repair is required. If any unsafe condition exists or unusual noises or movements are noticed and contact an authorized DHOLLANDIA agent. • [see Notice].
  • Page 24 Remember: if any part of the pre-trip inspection reveals a need for service or repair DO NOT use the tail lift until it has been serviced or repaired by a qualified service technician. Switch OFF power at the main battery disconnect switch or cabin switch see 9.5 page 35. DHOLLANDIA...

  • Page 25: Importance Of Preventative Maintenance

    Competent and regular preventative maintenance is essential to the operational reliability of the tail lift as well as the safety of • the operator and all bystanders. All maintenance and repair work must be performed by authorized DHOLLANDIA service agents, and using original • DHOLLANDIA replacement parts only.

  • Page 26: Load Charts And Correct Loading Procedures

    • load chart with great care. DHOLLANDIA disclaims liability for all personal bodily injury and / or property damage that results from overloading practices. • The maximum rated capacity is the maximum weight that the tail lift can carry under the following best possible circumstances: •...
  • Page 27 • For van tail lifts with narrow lift arms, the center point of maximum load is situated in the middle between the 2 lift arms, this is near the middle of the platform section supported by the tilt cylinders. ON THIS SIDE DHOLLANDIA...
  • Page 28 Keep the pallet jack and its load on the platform surface, as close as possible to the inboard platform edge. side edges of the platform. Lower and rest the pallet or load on the platform surface to prevent it from shifting position while lifting and lowering. DHOLLANDIA...
  • Page 29 / lower it on the platform. NEVER use the platform to level the ground • surface, or to push or pull loads or material by means of the platform. NEVER use the platform to move snow or other debris. DHOLLANDIA...

  • Page 30: Operating Instructions - Principles And Procedures

    Automatic tilt should be used with auxiliary controls which allow to LIFT / LOWER only: foot controls, 2-button handheld controls, 2- button fixed interior controls. DHOLLANDIA strongly recommends that you DO NOT use 3-button or 4-button handheld controls, that would also enable you to OPEN, CLOSE or TILT the platform.

  • Page 31: Remarks On Use Of The Tilt Cylinders

    Compensate for platform deflection by • setting its pitch a few degrees higher than DHOLLANDIA • EF0581.EN the intended pitch [note], when opening the platform. Note: the intended pitch is not always horizontal, it may depend on the slope of the ground.

  • Page 32: Main External Control Boxes

    DHOLLANDIA offers various control boxes, that may be purchased along with your tail lift upon initial order or may be purchased •...
  • Page 33 Safety point applied to the side of the body, to which the operator must point the transmitter in order to OPEN - CLOSE the platform. The safety point ensures that the driver stands clear of the range of motion of the platform while OPENING - CLOSING the platform. Operation: DHOLLANDIA...

  • Page 34: Most Popular Auxiliary Controls

    • distributor for more information, prior to ordering your tail lift. See contact info at page 3. The most popular options are outlined below. Contact your national DHOLLANDIA distributor for operation instructions on other • models, or models with different configurations, prior to operating the tail lift. See contact info at page 3.
  • Page 35 The van tail lifts are equipped with automatic tilt at ground level (see 9.1 page 29), operated from the functions LOWER and LIFT of the controls shown in this section. Handheld 3-button controls are NOT needed to tilt the platform at the ground. DHOLLANDIA...

  • Page 36: Switching The Main Power On/Off

    In case of combined system, (main battery disconnect and cabin switch) both must be switched on to activate the tail lift. Switching off only one of two will deactivate the tail lift, but it is strongly recommended to switch-off both. NEVER leave the main battery disconnect switch on while tail lift is not is use. DHOLLANDIA...

  • Page 37: Operation Of The Standard Platform

    29] and platform deflection under load it backwards. position has been reached. [see 9.2 page 30] LOWER the platform half-way to the Open the doors of the van and secure them Manually deploy the bridge plate. ground. in open position. DHOLLANDIA...
  • Page 38 Before lifting or lowering loads, make sure the loads are secured on the platform surface. Deploy the platform cart stops (if so equipped), lower loads on a pallet jack down on the platform surface or immobilize the load via equivalent securement device. DHOLLANDIA...
  • Page 39 Engage the platform stow lock by turning before closing the platform. NEVER closed vertical position and you hear the the pin and pushing it inside. CLOSE the platform before it is at hydraulic system turn in overpressure. maximum height at vehicle floor level. DHOLLANDIA...
  • Page 40 OPEN and CLOSE the platform at vehicle floor level only. Opening and closing the platform at a lower level can cause serious damage to the hydraulic cylinders of the tail lift. Consult the DHOLLANDIA website to view the operation video on the •...

  • Page 41: Operation Of The Lspz Platform

    29 ] and platform deflection under load pulling it backwards. before the horizontal work position has [see 9.2 on page 30]. been reached. LOWER the platform half-way to the Open the platform fold lock to clear the flip- Unfold the flip-over point. ground. over point. DHOLLANDIA...
  • Page 42 ALWAYS maintain 3 or death. points of contact. [see 7.4 on page 19]. DHOLLANDIA...
  • Page 43 Closing up in travel position Make sure the platform is below the rear Close the cart stops. Fold the bridge plate back onto the vehicle door bottom level and close the rear doors. floor. DHOLLANDIA...
  • Page 44 OPEN and CLOSE the platform at vehicle floor level only. Opening and closing the platform at a lower level can cause serious damage to the hydraulic cylinders of the tail lift. Consult the DHOLLANDIA website to view the operation video •...

  • Page 45: The Use Of Cart-Stops

    See page 3 for contact info. Consult the DHOLLANDIA website to view operation videos on the various types of cart-stop systems • (http://www.dhollandia.com/US/en-us/101/#/cat/0). www.dhollandia.com → Videos → General → Roll-stop systems OAP100.M = Manual cart-stops, operated by springs...
  • Page 46 CLOSE Kick the lever into position 1. Step on the cart-stop flap. DHOLLANDIA...

  • Page 47: Decals

    NEVER remove or paint over any decal. • Missing, worn or illegible warning decals must be immediately replaced. Get free replacement decals from DHOLLANDIA. ❾ ❾ Contact your regional DHOLLANDIA distributor. See page 3 for contact info. The operator should comply with all •...
  • Page 48 250mm from the inboard edge of the platform adjacent to the rear sill of the vehicle body. EXAMPLE ❸ ❻ DHOLLANDIA...
  • Page 49 Tail lift decals used and affixed in areas, other than the rear of the vehicle: • ⓫ ❿ For circuit breaker in tail lift battery compartment Cabin switch in driver’s cabin to switch electrical power to tail lift on / off (if so equipped) For main fuse in tail lift battery compartment DHOLLANDIA...

  • Page 50: Meaning Of Safety And Warning Signs

    11 MEANING OF SAFETY AND WARNING SIGNS MANDATORY ACTION signs WARNING signs Contact your regional DHOLLANDIA distributor. Overview and keep visual control over the working area of the tail lift at all times. Consult the DHOLLANDIA website. General warning sign, used to alert the user to potential hazards.
  • Page 51 Switch OFF the electrical power to the tail lift via the main battery disconnect switch and / or cabin switch. This is an operation to be executed manually (as opposed to an electrical function controlled by means of one of the control units). DHOLLANDIA...

  • Page 52: End Note

    Competent and regular preventative maintenance is essential to the operational reliability, and the safety of the operator and • bystanders. All maintenance and repair work should be performed by authorized DHOLLANDIA service agents, and using only authorized • OEM DHOLLANDIA replacement parts.

This manual is also suitable for:

Dh-lspz.05Dh-lsp.07Dh-lspz.07

Table of Contents