Related Manuals for Atlas Copco HiLight V2+
Summary of Contents for Atlas Copco HiLight V2+
- Page 1 Instruction Manual Instruction Manual for Portable Light Tower Generator English HiLight V3+ WUX Engine P2000I HiLight V2+ WUX Engine P3000 HiLight P2+ WUX Engine P6500...
- Page 3 Instruction Manual for Portable Light Tower Generator HiLight V3+ WUX HiLight V2+ WUX HiLight P2+ WUX Printed matter No. 9829 3868 00 ATLAS COPCO - PORTABLE ENERGY DIVISION www.atlascopco.com 12/2017...
- Page 4 Neglecting maintenance or making changes to the setup of the machine can result in major hazards, including fire risk. While every effort has been made to ensure that the information in this manual is correct, Atlas Copco does not assume responsibility for possible errors.
-
Page 5: Table Of Contents
Table of contents Preface Operation ..........23 Starting the engine of HiLight V3+ and Please read the following instructions carefully before starting to use your machine. Follow the HiLight V2+..........23 Safety Precautions ........7 instructions in this booklet and we guarantee you Starting the HiLight P2+ ...... - Page 6 - 6 -...
-
Page 7: Safety Precautions
- Fill or drain the fuel tank in an area with good the winch or the mast malfunction, stand away airflow. from the light tower and contact Atlas Copco. The light tower has moving parts. Moving parts can cut or crush body Engine exhaust and fuel fumes can cause parts. -
Page 8: Safety Before Servicing
If there is a problem for problems in the reproductive system. servicing, speak to Atlas Copco. All • To prevent fire or burns, do these steps: servicing must be done when the engine... -
Page 9: Leading Particulars
LEADING PARTICULARS GENERAL DESCRIPTION The HiLight V3+, HiLight V2+ and HiLight P2+ are portable light-towers. They have LED (Light Emitting Diode) lamps that can illuminate an average area of 2000m HiLight V3+ and HiLight V2+ The HiLight V3+ and HiLight V2+ consist of the following parts: HiLight HiLight Beam... - Page 10 Engine HiLight HiLight P2+ The engine is coupled to a generator, which energizes The HiLight P2+ is a light-weight and flexible light LAMP the LED lamps. The engine operates on petrol. tower. It can be lifted and moved by the operator. LED lamp The HiLight V3+ lamp configuration has 4 bulbs of HiLight...
- Page 11 Power plug The HiLight P2+ is a “Plug-and-light” light tower. It must be energized by a local power source. LED lamp The HiLight P2+ has a 320W balloon LED lamp. It is a non-inflatable balloon LED lamp. The lamp illuminates an area in all directions (360° area). HiLight LAMP - 11 -...
-
Page 12: Markings And Information Labels
MARKINGS AND INFORMATION LABELS Drain condensate daily from Check oil level in engine vessel Check coolant level Rotation direction. Check petrol in the fueltank Service point. Read the instruction manual Lifting permitted. before filling oil Read the instruction manual before lifting. Dangerous outlet gases. -
Page 13: Product Drawings
PRODUCT DRAWINGS GENERAL ARRANGEMENT DRAWINGS HiLight V3+ - 13 -... - Page 14 HiLight V2+ - 14 -...
- Page 15 HiLight P2+ - 15 -...
-
Page 16: Circuit Diagrams
CIRCUIT DIAGRAMS COMPREHENSIVE WIRING SCHEMATIC DIAGRAM FOR LAMP CIRCUIT- 9829 3800 74 - 16 -... -
Page 17: Generator-Capacitor Excitation Schematic Diagram
GENERATOR-CAPACITOR EXCITATION SCHEMATIC DIAGRAM Reference Description Rotor Stator Excitation coils Capacitor Generator/terminal block Control box lights Wire Colours Black Brown Clear Green Grey Blue Light Blue Orange Pink Purple Shield Violet White Yellow - 17 -... -
Page 18: Trailer Wiring Diagram
TRAILER WIRING DIAGRAM- 1094 2932 00 Reference Description Wire Colours Right stop, turn, and tail lights Green Right stop and turn lights Left stop, turn, and tail lights Yellow Left stop and turn lights Side light, amber Brown License plate, tail, and side lights Side light, red White... -
Page 19: Comprehensive Wiring Schematic Diagram For Engine Circuit
COMPREHENSIVE WIRING SCHEMATIC DIAGRAM FOR ENGINE CIRCUIT- 9829 3800 78 - 19 -... -
Page 20: Deployment And Operation
DEPLOYMENT AND OPERATION • The lifting eye (LE) for the unit is above the engine. • Use lifting and loading equipment, e.g. slings, hooks, chains, ramps, etc. of Before using the HiLight V2+ or HiLight V3+ or HiLight P2+, the correct rating. The gross vehicle weight rating of the light tower is given read the instruction manual carefully. -
Page 21: Deployment Of Hilight V3+ And Hilight V2
Towing 2. During towing • Do not load the unit with parts or tools. CAUTION FOR LOCKING SCREW: • Do not tow light towers one after the other as a group. If care is not taken, the locking screw (LS) can scratch the mast (M) or prevent •... -
Page 22: Deployment Of Hilight P2
Deployment of HiLight P2+ CAUTION FOR LOCKING SCREW: If care is not taken, the locking screw (LS) can scratch the mast (M) Before using the HiLight P2+, read the instruction manual carefully. or prevent the inner mast from getting raised. Obey all instructions given in the manual. -
Page 23: Operation
OPERATION 5. Release the key when the engine starts. Release as below: the key if the engine does not start in 10 1. Turn the key to "OFF" position and wait for 60 seconds. Starting the engine of HiLight V3+ and HiLight seconds. -
Page 24: Starting The Hilight P2
b) Adjusting the lamp direction for HiLight V3+ Starting the HiLight P2+ a) Raising the mast 1. Unscrew the locking pin (1) and rotate the light The HiLight P2+ is a “plug-and-use” light tower. It 1. Rotate the handle of the winch (1) till the lamp must be connected to a power source to energize the reaches the necessary height. -
Page 25: Operating The Led Lamps
2. Lowering 2. De-energizing the LED lamps a) De-energizing the LED lamps for HiLight V3+ and HiLight V2+ Before moving the light tower, lower the mast and lock it in place. This prevents injury caused by falling objects. Always break the electrical circuit before stopping the engine. This prevents damage to the LED lamps and generator. -
Page 26: Maintenance
MAINTENANCE 1. Replacing the lamp for HiLight V3+ Do all maintenance activities when the light tower is de-energized. Touching live electrical circuits can cause electric shock and can result in injury or death. REGULAR INSPECTION Do the following inspection regularly: •... -
Page 27: Engine Maintenance
2. Replacing the lamp for HiLight V2+ and HiLight P2+ ENGINE MAINTENANCE Refer to the Engine Instruction Manual for precautions and maintenance of the engine. Replacing parts See the Parts Manual for more information. Remove the 8 screws (1) using a pneumatic tool. Lift and remove the LED protective cover (3) by using the handles (2). -
Page 28: Maintenance Schedule
MAINTENANCE SCHEDULE - P2000I Maintenance Item Schedule Routine Pre-operation 6 months or 12 months or (running hrs) check (daily) 100 hrs 300 hrs Spark plug Check condition. Clean and replace if necessary. Fuel Check fuel level and leakage. Fuel hose Check fuel hose for cracks or damage, Replace if necessary Check oil level in engine. -
Page 29: Maintenance Schedule
MAINTENANCE SCHEDULE - P3000 AND P6500 Schedule for regular maintenance Per use Every 50 hours or Every 100 hours or Every 300 hours every 3 months (3) every 6 months (3) or every year (3) Engine oil Inspect the oil level Replace Air cleaner Inspect... -
Page 30: Technical Specifications
TECHNICAL SPECIFICATIONS Reference conditions unit HiLight V3+ HiLight V3+ HiLight V3+ HiLight V2+ HiLight V2+ HiLight V2+ HiLight with P2000I with P3000 with P6500 with P2000I with P3000 with P6500 Rated frequency 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60... -
Page 31: Performance Data
Performance data unit HiLight V3+ HiLight V3+ HiLight V3+ HiLight V2+ HiLight V2+ HiLight V2+ HiLight P2+ with P2000I with P3000 with P6500 with P2000I with P3000 with P6500 1. Rated active power (PRP) 1ph 2. Rated power factor (lagging) cos f 1phase Rated apparent power 1ph... -
Page 32: Data Plate
DATA PLATE The data plate in on the Base frame of the light tower. - 32 -...
Need help?
Do you have a question about the HiLight V2+ and is the answer not in the manual?
Questions and answers