Table of Contents
Advertisement
HC 400 Series • Setup Guide (Continued)
Cabling
Attach cables using the following wiring diagrams as a guide. Full details are available in the HC 400 Series User Guide.
AV Inputs
Analog audio input
For analog audio sources, connect the source device to the audio input 3.5 mm tip-ring-sleeve (TRS)
connector on the transmitter (see figure 4 and figure 5,
the connector as shown at right.
Analog video input
Connect an analog RGB video input source to the 15-pin HD RGB input connector (
.
Digital AV input
For HDMI video and for digital audio embedded within HDMI signals:
Connect a digital video source device to any HDMI input connector on the
1.
transmitter or receiver (see
To secure each cable to the unit, attach an Extron LockIt
2.
secure it to the cable with a zip tie.
Plug the HDMI cable into the panel connection (see
a.
Loosen the HDMI connection mounting screw from the panel enough to allow the
b.
LockIt lacing bracket to be placed over it (
removed.
Place the LockIt lacing bracket on the screw and against the connector (
c.
tighten the screw (
Loosely place the included tie wrap around the connector and the LockIt lacing
d.
bracket as shown (
While holding the connector securely against the lacing bracket, tighten the tie
e.
wrap, then remove any excess length.
Complete details on LockIt installation are available in the LockIt HDMI Cable Lacing
Bracket Installation Guide.
Transmitter-Receiver Interconnection
Connect the Out port of the transmitter (figure 4,
shielded twisted pair CAT x cable of up to up to 230 feet (70 m), as shown in
Terminate the cable with shielded RJ-45 connectors using the TIA/EIA-T568B wiring standard
at both ends, as shown at right.
ATTENTION:
• Do not connect this port to a computer data network or a telecommunications network.
• Veuillez ne pas connecter ce port à un réseau de données informatiques ou à un
réseau de télécommunications.
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable.
• N'utilisez pas le câble AV Skew-Free UTP version améliorée UTP23SF-4 d'Extron ou
le câble STP201.
For optimal performance, Extron highly recommends the following:
•
Use the TIA/EIA-T568B wiring standard for terminating all STP cables with RJ-45 connectors.
•
Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable bandwidth of 400 MHz.
•
Use shielded RJ-45 plugs to terminate the cable.
•
Overall transmission distance capabilities vary depending on the number of patches used. If possible, limit the number of
patches to 2 total.
•
If patches must be used in the system, Extron recommends shielded CAT 6 (or better) patch cables.
12
B
D
in
Rear and Side Panel Features
b
). The screw does not have to be
d
) to secure the bracket.
e
).
E
) to the In port of the receiver (
on page 4 for connector location). Wire
C
) on the transmitter
on page 4).
bracket to the unit and
®
a
at right).
c
), then
F
) using a
figure 1
on page 2.
Tip (L)
Ring (R)
Sleeve (Gnd)
3.5 mm Stereo Plug
(unbalanced input)
b
a
c
3
d
e
Pins:
TIA/EIA-T568B
12345678
Pin
Wire color
1
White-orange
2
Orange
3
White-green
4
Blue
5
White-blue
6
Green
7
White-brown
8
Brown
Insert twisted
pair wires.
Advertisement
Table of Contents
