Table of Contents
Advertisement
HC 400 Series • Setup Guide (Continued)
Prepare the Installation Site for the HCT 102 D
ATTENTION:
Installation and service must be performed by authorized personnel only.
•
L'installation et l'entretien doivent être effectués uniquement par un technicien qualifié.
•
• Extron recommends installing the HCT 102 D into a grounded, UL Listed electrical junction box.
• Extron recommande d'installer le HCT 102 D dans un boîtier d'encastrement électrique mis à la terre, certifié UL.
If the controller will be installed into fine furniture, it is best to hire a licenced, bonded craftsperson to cut the access
•
hole and perform the physical installation so the surface will not be damaged.
S'il est prévu d'installer le contrôleur dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et
•
qualifié pour couper le trou d'accès et réaliser l'installation de telle façon que la surface ne soit pas endommagée.
Follow all national and local building and electrical codes that apply to the installation site.
•
Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s'appliquent au site de l'installation.
•
NOTE:
For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the HCT 102 D must be
installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with the unit.
Americans with Disabilities Act (ADA) compliance
When planning where to install the MLC Plus 50/100/200, you may need to consider factors affecting accessibility of the
controller such as height from the floor, distance from obstructions, and how far
a user must reach to press the buttons. For guidelines, see sections 307
("Protruding Objects") and 308 ("Reach Ranges") of the
2010 ADA Standards for Accessible Design available
http://www.ada.gov/regs2010/2010ADAStandards/2010
at
ADAStandards.pdf.
Site preparation
Mud rings, optional UL Listed junction boxes, external
junction boxes, and surface mounting boxes are available
for use with the HCT 102 D.
Read any installation instructions and UL guidelines
1.
that come with the mounting devices.
Protect the mounting surface to prevent damage.
2.
For a junction box or mud ring, cut a hole in the wall
3.
or furniture just large enough to insert the box or mud
ring. Cutout dimensions for the 2 gang mud ring are
4.06 inches W x 3.75 inches H (104 mm W x 95 mm H).
The cutout for a junction box varies by model.
Install the box or mud ring in the opening at the
4.
installation site.
Run cables to the mounting location, leaving enough
5.
slack for device installation. Secure the cables with a
clamp for strain relief so they do not slip back down
into the wall or furniture.
Step 3 — Connect AV, Interconnection, and Control Cables
Connect AV sources to the input connectors (see
1.
Use a shielded twisted pair cable to connect the transmitter to the receiver via the Output and Input RJ-45 connectors (see
2.
Transmitter-Receiver Interconnection
Connect AV output devices (display, projector, or other device, and an amplifier or powered speakers) to the output
3.
connectors (see
AV Outputs
If applicable, use Extron Show Me cables or connect a remote keypad to the Remote ports on the transmitter for controlling
4.
and indicating input selection (see instructions for the Remote connectors in
Cable the control ports on the receiver as desired for controlling AV devices and for communicating with the system via LAN
5.
(see
Control
on page 13).
6
AV Inputs
on page 12).
on page 13).
4.06"
3.75"
Installing a Mud Ring
Figure 7.
on page 12).
Control
on page 13).
Wall
Mud Ring
Advertisement
Table of Contents
