Extron electronics HC 404 Setup Manual page 15

Power
ATTENTION:
• Always use a power supply supplied or specified by Extron. Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply and the unit.
• Utilisez toujours une source d'alimentation fournie par Extron. L'utilisation d'une source d'alimentation non autorisée annule toute
conformité réglementaire et peut endommager la source d'alimentation ainsi que l'unité.
For port locations, see figure 4
• Connect the included 12 VDC, 4.2 A power supply (Extron PS 1242) at the receiver to remotely power the transmitter.
HCT 103
Rear Panel
2 3
POWER
12V AUDIO
0.5A MAX
RGB HDMI
INPUTS
R
HCR 102
Front Panel
NOTE: The receiver can provide power remotely to the transmitter using a 50 watt power supply. Remote power mode
requires at least 2.5 A. The transmitter can receive power from but cannot provide power to the receiver. The remote
power feature is enabled by default but can be disabled by using a control in the PCS software.
• Alternatively, you can connect an optional 12 VDC, 1.5 A power supply (Extron PS 1215 C) or
(for the HCT 103 only) a 12 VDC, 0.5 A power supply (Extron PS 1205 C) at the transmitter, and
connect an optional 12 VDC, 2 A power supply (Extron PS 1220) at the receiver.
HCT 103
Rear Panel
2 3
POWER
12V
AUDIO
0.5A MAX
RGB HDMI
INPUTS
Ridged
– Return
+12 VDC input
Smooth
18 watt
Transmitter Power Input
• Connect to optional
12 VDC, 1.5 A power supply.
For both options, connect the external power supply or supplies to a 100 to 240 VAC power source.
A
and figure 5, on page 4. You have two options for powering the system:
AV, Communication, Power
4 SIG LINK
REMOTE
CONTACT TALLY
HDMI OUT
1 2 3 G 1 2 3 +V
Remote Power:
50 watt Receiver Power Input
• Receiver front panel • Connect an included
LED ( ) blinks
12 VDC, 4.2 A power
during boot-up and supply to the receiver
remains lit when the only. The receiver
unit is powered and supplies power to
operational. the transmitter.
AV and Communication Only
4 SIG LINK REMOTE
CONTACT TALLY
HDMI
OUT 1 2 3 G 1 2 3 +V
To
AC
power
External
Power Supply
(12 VDC, 1.5 A max.,
Extron P/N 28-327-57LF)
NOTE: Check the
polarity of each
power supply
before connecting
it to a unit.
INPUTS SIG LINK
POWER
HCT 103
12V
1 TP
2.0A MAX
HDMI IN
To AC power
Ridged
– Return
+12 VDC input
Smooth
INPUTS SIG LINK
POWER
HCT 103
12V
1 TP
2.0A MAX
HDMI IN
To AC power
Ridged
– Return
+12 VDC input
Smooth
24 watt Receiver Power Input
• Connect to optional • Receiver front panel LED (
12 VDC, 2 A
power supply.
COM IR DIGITAL I/O
OUTPUTS
AUDIO
L R
HDMI/CEC Tx Rx G S G 1 2 G 3 4 G
Ground all devices.
Power Supply
(12 VDC, 4.2 A max.,
Extron P/N 28-394-07LF )
OUTPUTS COM IR DIGITAL I/O
AUDIO
L R
HDMI/CEC Tx Rx G S G 1 2 G 3 4 G
Ground all devices.
Power Supply
(12 VDC, 2 A max.,
Extron P/N 28-284-07LF)
) blinks
during boot-up and remains lit when
the unit is powered and operational.
HCR 102
Rear Panel
HCR 102
LAN
External
HCR 102
Rear Panel
HCR 102
LAN
External
R
HCR 102
Front Panel
15