Subscribe to Our Youtube Channel
Related Manuals for Allnet ALL168255
Summary of Contents for Allnet ALL168255
-
Page 1: Quick Installation
ALL168255 QIG English ALL168255 500 Mbps PLC Ethernet Bridge QUICK INSTALLATION REFACE This document describes installation of the 500Mbps PLC Ethernet Bridge Network products. ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 1... - Page 2 This publication contains the following sections: Important safety instructions The first thing you need to know before you begin to install Product installation guide Specification ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 2...
- Page 3 If the product has been exposed to rain or water. If the product does not operate normally when the operating instructions are followed. If the product exhibits a distinct change in performance. ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 3...
- Page 4 To meet the safety regulation, the longest distance between powerline carrier devices will be limited at 100 meter and for in-house use only. More than 100 meter will cause the signal reduction or data loss. ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 4...
- Page 5 Plug the provided Ethernet cable into the RJ45 connector of the Bridge and plug the other end of the cable into the Ethernet port on the wireless AP. ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 5...
- Page 6 ALL168255 QIG English User diagram: PLC Net Plug Set Top Box PLC Net Plug Internet Networ PLC Net Plug DSL or Cable Modem ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 6...
-
Page 7: Specification
Operating : 10~85% Non-Condensing Storage : 5~90% Non-Condensing 100 ~ 240 VAC 50/60Hz Power Source Power ca. 2W (Normal mode), less than 0.5W (Standby mode) Consumption Certification ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 7... -
Page 8: Push Buttons
Ethernet cable, it will get into standby mode after 60 seconds. Under standby mode, PLC and ETH LEDs will both be off. Push Buttons (Only applicable for models with push button) Push button functions are disabled when in Standby mode! ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 8... - Page 9 Push the device’s “NID/RST” button for 10-15 sec seconds. You will see the device’s LEDs are all turning off and the device will restart. The device’s setting resets to the “factory defaults”. ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 9...
- Page 10 2. Install the Powerline Utility from the provided CD. After the installation connect your PC directly to one of the 2 Powerline-Bridges. 3. Start the Software and click on “Set” under “Main” --> “Security. ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 10...
- Page 11 If all devices are plugged in next to each other you can afterwards also check the data throughput. If you think that something is wrong with the powerline-bridges, please contact the ALLNET-support. ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 11...
-
Page 12: Declaration Of Conformity
Address: Allnet GmbH Maistraße 2 82110 Germering Germany E-Mail: info@allnet.de support@allnet.de Germering, August 28, 2012 Phone: +49 (0)89 894 222 22 Fax: +49 (0)89 894 222 33 ALL168255 Quick Installation Guide © 2012 ALLNET GmbH All rights reserved Page 12...
Need help?
Do you have a question about the ALL168255 and is the answer not in the manual?
Questions and answers