ORiNG IES-180-L Quick Installation Manual

SWITCH
I N D U S T R I A L
Q I
uick nstallation
Introduction
IES-180-L is an unmanaged Ethernet switch with eight 10/100Base-T(X)
ports in a compact form factor. The easy-to-install switch comes with rigid
IP-30 housing and can operate in harsh environments. The wide operating
o o
temperature range from -20 C to 60 C ensures the switch can operate reliably
in extreme weather conditions.
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Contents Pictures Number
IES-180-L
DIN-rail Kit
Wall-mount Kit
QIG
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed cabinet, the operating
ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
Reduced Air Flow: Installation of the equipment should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
Mechanical Loading: Mounting of the equipment in the d
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
IES-180-L
G
uide
Dimension (Unit: mm)
PWR PWR
P7 P7
P5 P5
P3 P3
X 1
P1 P1
10/100TX 10/100TX
IES-180-L IES-180-L
X 1
X 2
Panel Layouts
X 1
Front Panel
1
PWR PWR
LNK /ACT LNK /ACT
2
3
P7 P7
P5 P5
P3 P3
P1 P1
10/100TX 10/100TX SPEED SPEED
IES-180-L IES-180-L
Real Panel
in-rail should be
1
2
1
1907-2-29-IES180L-1.0
IES-180-L
LNK /ACT LNK /ACT
P8 P8
P6 P6
P4 P4
P2 P2
SPEED SPEED
10M 10M
100M 100M
25.00
Top Panel
1. PWR LED
2. Link/Act indicator for LAN port
3. LAN port
DC10 ~ 30V
V+ V-
P8 P8
1
P6 P6
1. Terminal block
P4 P4
P2 P2
10M 10M
100M 100M
1. Wall-mount screw holes
2. Din-rail screw holes
PRINTED ON RECYCLED PAPER
Industrial Unmanaged Switch
Installation
DIN-rail Installation
Step 1: Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Step 2: Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into
the rail firmly.
Wall-mounting
Step 1: Screw the two pieces of wall-mount kits onto both sides of the switch. A
total of eight screws are required, as shown below.
Step 2: Use the switch, with wall mount plates attached, as a guide to mark the correct
locations of wall-mount screws.
Step 3: Insert screw through the large parts of the keyhole-shaped apertures, and then slide
the switch downwards. Tighten the four screws for added stability.
Quick Installation Guide
Version 1.0
PWR PWR
LNK /ACT LNK /ACT
P7 P7 P8 P8
P5 P5 P6 P6
P3 P3 P4 P4
P1 P1 P2 P2
10/100TX 10/100TX SPEED SPEED
10M 10M
IES-180-L IES-180-L 100M 100M