Download Print this page
3M 8832-JG1 UPC SM Instructions Manual
3M 8832-JG1 UPC SM Instructions Manual

3M 8832-JG1 UPC SM Instructions Manual

No polish lc jg1 connector for 1.6-2 mm cable

Advertisement

Quick Links

3M™ No Polish LC JG1 Connector for 1.6-2 mm cable
8832-JG1 UPC SM
6832-50/OM2-JG1 MM
6832-50/OM4-JG1 MM
Instructions
January 2016
OPT01-IN-178B(E)
3

Advertisement

loading
Need help?

Need help?

Do you have a question about the 8832-JG1 UPC SM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for 3M 8832-JG1 UPC SM

  • Page 1 3M™ No Polish LC JG1 Connector for 1.6-2 mm cable 8832-JG1 UPC SM 6832-50/OM2-JG1 MM 6832-50/OM4-JG1 MM Instructions January 2016 OPT01-IN-178B(E)
  • Page 2: Safety Precautions

    Never look directly into the fiber or connector using the naked eyeor a microscope. Overview 3M™ No Polish Connectors 8832-JG1 & 6832-JG1 termi- nate 1.6mm and 2.0mm jacket cable...
  • Page 3 Materials required for connector termination You will find following components in a box of connectors. A. 3M No Polish Connector 8832-JG1/6832-JG1 B. Boot C. Cable holder D. Disposable stripper (for 250um coating removal only, up to 20 stripping) Note: content may vary depending on product you purchased...
  • Page 4: Termination Process

    Termination process Put connector boot on cable Remove cable jacket 50mm from the cable end. Cable holder can be used to measure the length. Align the end of cable to the double line on the cable holder to meas- ure 50mm. Butt up jacket end against the stop on the cable holder as shown.
  • Page 5 Lay the cable straight on the cable holder. Place the ca- ble in appropriate position in the clamp depending on fiber type inside cable jacket. And close the cover to clamp cable Upper position: cable with 900um coated fiber inside Lower position: cable with 250um coated fiber inside Make sure fiber sit in fiber guide slit in sliding connect-...
  • Page 6 Fully pull out sliding connector nest from the cable holder. Put marking(s) on the fiber with a marking pen 1st marking: at the edge of holder body 2nd marking: at the indicator “0.9” (900um fiber only) 2nd marking 1st marking (900um fiber only) Marking locations for cable with 250 m fiber inside Marking locations for cable with 900 m fiber inside...
  • Page 7 Stripping 900 m fiber Remove coating at the 2nd marking and outward with appropriate stripping tool. Thoroughly clean the stripped fiber with a lint-free wipe and alcohol or cleaning fluid. Test the stripped fiber for weak points by using your finger to slowly flick the fiber in multiple directions.
  • Page 8 2.10 Check for cleave length and strip length by pulling out sliding connector nest of cable holder. 900 m buffer end Glass fiber end 250 m buffer end Fiber end/buffer end must be within respective gauge window (900 m buffer shown as example) Too short Right length Too long...
  • Page 9 2.13 Be aware of fiber guide protruding downward until splice is acutated Caution: Do NOT PUSH UP fiber guide or connector may pop out from cable holder 2.14 Check for buffer clamp. If the clamp is partially actuated, remove the connector and repeat at Section 2.12 2.15 Hold the cable holder by both sides.
  • Page 10 2.17 Flip back actuation lever on the dust cap and fully press down the lever 2.18 Check if cap is fully actuated. If not, press down lever again 2.19 Slide boot next to the holder 2.20 Release holder cover and bring boot closer to connector...
  • Page 11 2.21 Remove aramid yarn from the slot and lay it on connect- 2.22 Hold aramid yarn and connector TOGETHER and re- move from the cable holder. Caution: Keep holding aramid yarn and connector togeth- er until boot is secured to the connector. Failure to do so may induce twist in fiber resulting in fiber break later 2.23 WHILE HOLDING ARAMID YARN AND CONNECTOR TOGETHER WITH ONE HAND, take...
  • Page 12 2.24 Bring boot up to connector Caution: Keep holding aramid yarn and connector togeth- er until boot is secured to connector. Failure to do so may induce twist in fiber resulting in fiber break later 2.25 Fully tighten boot WHILE HOLDING ARAMID YARN AND CONNECTOR TOGETHER.
  • Page 13 Duplexing No Polish LC-JG1 Connectors No Polish LC-JG1 can be duplexed without using extra parts. Two connectors can dovetail together to form duplex connector Identify dovetailing features on both sides of connector body Dovetail two connectors to assemble them together Make sure latches are fitting together...
  • Page 14 Connector re-open Insert two folks on the dust cap into slots on back side of connector Unscrew and remove boot from connector. Pull out buffer clamp with fingers then remove fiber from the connector...
  • Page 15 Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of 12 months from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FIT- NESS FOR A PARTICULAR PURPOSE.

This manual is also suitable for:

6832-50/om2-jg1 mm6832-50/om4-jg1 mm