Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Esse-ti HELPY GSM-RM
Summary of Contents for Esse-ti HELPY GSM-RM
-
Page 1: Quick Guide
Alarm system for elevators QUICK GUIDE 14/12/2018... - Page 2 DESCRIPTION RJ45 connector for GSM satellite Jumper JP2 for define the behaviour of output AI Jumper JP4 for define the behaviour of output AR Built-in backup battery connector Internal power-supply connector Reset pushbutton Alarm pushbutton Built-in loudspeaker connector Serial port for PC connection Micro SD Card slot RJ11 connector for local telephone Battery compartment door...
- Page 3 LED HELPYGSM-RM LED signalling alarm / periodical test call (yellow) LED signalling GSM signal strength (green) (not used) LED signalling power supply status (blue) LED GSM SATELLITE LED signalling GSM status green LED signalling GSM signal strength DESCRIPTION Page 3...
-
Page 4: Terminal Blocks
Terminal blocks NAME DESCRIPTION 12 VDC OUTPUT (max. 100 mA) – NEGATIVE POLE GIVEN ALARM INDICATOR LIGHT (PNP/NPN by means of jumper JP2) RECEIVED ALARM INDICATOR LIGHT (PNP/NPN by means of jumper JP4) 12 VDC OUTPUT (max. 100 mA) COMMON TERMINAL FOR INPUT ALC –... - Page 5 INSTALLING NSTALLING THE ANTENNA AND INSERTING THE CARD IN THE SATELLITE Before proceeding, make sure the device is off and use all due precaution to avoid electrostatic discharge. Remove the GSM satellite cover. Screw the antenna in the appropriate connector (take care to only rotate the metal ferrule to fix the antenna;...
- Page 6 ONNECTING THE SPEAKER UNITS HelpyGSM-RM comes with a built-in active speaker unit. It is also possible to connect to the HelpyGSM-RM: up to 2 independent active speaker units up to 2 passive speaker units (or cables with microphone) combined to the integrated active speaker unit.
- Page 7 Installation with active speaker unit in the pit SPEAKER UNIT PUSHBUTTON DEVICE terminal blocks terminal blocks ROOF HelpyGSM-RM Built-in active speak. unit Built-in pushbutton – – Microphone cable MIC3 / ALC / – – Active speak. unit VVY / ALY / PROGRAMMING CODES "TYPE OF INSTALLATION"...
- Page 8 ONNECTING THE EMERGENCY CALL BUTTONS Car pushbutton It is possible to connect (inside the elevator car) voltage free contact pushbuttons or powered pushbuttons. Connect, following one of the diagrams shown below, the car pushbutton. Voltage free contact pushbuttons Powered pushbuttons (12~24Vdc) – 2 solutions Page 8 INSTALLING...
- Page 9 Other pushbuttons It is possible to use for the pit, the car-top or the landing floors, voltage free contact pushbuttons (NO). Connect, following the diagram shown below, the other pushbuttons. INSTALLING Page 9...
- Page 10 ONNECTING THE INDICATOR LIGHTS The GIVEN ALARM INDICATOR LIGHT (yellow) switches on after pressing the emergency button to indicate the beginning of the alarm procedure and stays steady light until the end. The RECEIVED ALARM INDICATOR LIGHT (green) switches on when the alarm call is answered. ...
-
Page 11: Connecting The Relay
Note: the ALZ input must be programmed as auxiliary input (by setting parameter 55). ONNECTING THE RELAY Connect the output RL1 (normally open contact) to the external device. EPLACING BATTERY ATTENTION Only use replacement batteries supplied by Esse-ti. INSTALLING Page 11... -
Page 12: Wiring Diagram
– E IRING DIAGRAM XAMPLE Page 12 INSTALLING... - Page 13 – E IRING DIAGRAM XAMPLE INSTALLING Page 13...
-
Page 14: Power Connection
OWER CONNECTION Connect the power supply cable to the 230Vac mains. Connect the built-in backup battery cable to the slot C in the picture at page 2. Note: the power supply cable's plug must be always easily accessible. Note: a protection cut-out switch must be installed upstream to interrupt power supply in case of fault. - Page 15 INIMUM OPERATIONS TO VERIFY PROPER INSTALLATION 1. PROGRAMMING Access to programming: lift the local telephone handset and dial The programming activated message will be heard. Program a telephone number for the emergency-call alarm: dial < telephone number > ...
-
Page 16: Resetting The Alarm
mode: automatic handsfree connection without messages Answer by the called party. Speak with the trapped person. 4. RESETTING THE ALARM Note: the alarm reset mode can be configured with the “Alarm reset mode” programming (code 77). mode: reset by “End” code (factory default) ... -
Page 17: Using The Reset Button
EU D ECLARATION OF ONFORMITY Hereby, Esse-ti S.r.l. declares that the radio equipment type HelpyGSM-RM is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available from the following Internet address: https://www.esse-ti.it/en/dichiarazioni-di-conformita... -
Page 18: Basic Programming
EXITING THE <INSTALLER or OPERATOR PASSWORD> PROGRAMMING (factory setting: SOURCE RECEIVER emergency- — call button battery USER alarms periodic automatic test ESSE-TI call … — (X…X = TELEPHONE telephone (position NUMBERS number, SIM card from 01 to (INST) max 20... -
Page 19: Installation
BASIC PROGRAMMING DELETING TELEPHONE ( position from 01 to NUMBER (INST) only the built-in active speaker unit built-in active speaker unit and 1 active speaker unit Number of connected active speaker built-in active speaker unit TYPE OF units and 2 active speaker units INSTALLATION connected (INST) - Page 20 (hhmm; from 0000 to 2359) call AUTOMATIC TEST DATA Enabling automatic test disabled (INST) automatic test automatic test enabled Manually perform a test call PROTOCOLS Esse-ti IDENTIFICATION … (identification CODE code) P100 (INST) built-in active speaker unit SPEAKER UNITS loudspeaker...
-
Page 21: Advanced Programming
BASIC PROGRAMMING GENERAL loudspeaker microphone messages VOLUME (from 1 to 5; from 8 to 9; (from 1 to (INST/OPER) factory default factory 5; factory default 8) default 2) LISTEN TO THE PROGRAMMING (programming code prefix) AGAIN (INST) RESTORE FACTORY SETTINGS (INST) Advanced programming ADVANCED PROGRAMMING... -
Page 22: Auxiliary Alarm
ADVANCED PROGRAMMING AUXILIARY disabled alarm ALARM (INST) enabled alarm disabled alarm SIM CARD EXPIRING enabled alarm ALARM Last (INST) recharge (dd) (mm) (yy) date disabled ENABLE FILTER (INST/OPER) enabled FILTER INPUT normally closed NORMALLY CLOSED/OPEN (INST/OPER) normally open ALARM AI indicator light lit and courtesy message OPERATION WITHOUT AI indicator light unlit and no courtesy message... - Page 23 ADVANCED PROGRAMMING “END ALARM” CODE … (from 1 to 3 digits; factory default 9) (INST) “EXCLUSION” CODE … (from 1 to 3 digits; factory default 1) (INST) identification message RESET MESSAGES (INST) courtesy message CHANGE (language: 00 Italian, 01 English, 02 German, LANGUAGE 03 French, 07 Spanish) (INST)
- Page 24 ADVANCED PROGRAMMING CONNECTION DURATION AFTER AUTOMATIC (minutes, from 1 to 9) RESPONSE (INST) same behaviour as output AI same behaviour as output AR active for external power failure RELAY SETTING door opener (INST) active as long as the emergency alarm progresses active as long as the buttons are pressed active for telephone line absence RELAY...
- Page 25 - set a micro SD card to use for programming, customizing the messages and updating the firmware of the HelpyGSM-RM. e-stant can be downloaded at the following link: https://www.esse-ti.it/download/richiesta-software Programming via micro SD card The micro SD card properly set allows to:...
-
Page 26: Programming Via Sms
Programming via SMS Programming via SMS can be performed from any mobile phone or other device that can send SMS messages. An SMS notifying the programming was performed is sent by the HelpyGSM-RM to the number that sent the programming. ATTENTION Programmed performed via SMS sent from the Internet could not have a positive result if the... -
Page 27: Local Use
Local use In the tables: : lift the local telephone handset : lift the local telephone handset and dial to access programming LOCAL USE CONVERSATION CONVERSATION WITH THE CAR CAR SPEAKER UNIT CONVERSATION SPEAKER UNIT CONNECTED TO VVY WITH ONE SPEAKER UNIT SPEAKER UNIT CONNECTED TO VVX DEACTIVATE ALL... - Page 28 SIGNALS LED signalling alarm / periodical test call (yellow) Emergency-call alarm Emergency call alarm suspended Other alarms - Test call LED signalling GSM signal strength (green) No signal Low signal level Medium signal level Good signal level High signal level Note: the green LED on GSM satellite turns on during a call or when the local telephone is used.
- Page 29 LED signalling GSM status (red) HelpyGSM-RM correctly registered on the network HelpyGSM-RM registering to the GSM network – HelpyGSM-RM not registered correctly – PIN request – PIN incorrect – Other problems Call in progress LED signalling power supply status (blue) The external power supply is connected and the battery has max capacity charge The external power supply is connected and the battery has good capacity...
- Page 30 The external power supply is disconnected and the battery guarantees up to 7-hour operation in idle state The external power supply is disconnected and the battery guarantees 2-hour operation in idle state The external power supply is disconnected and the battery guarantees 1-hour operation in idle state Page 30 SIGNALS...
-
Page 31: Troubleshooting
TROUBLESHOOTING DETECTED PROBLEM ROOT CAUSE SOLUTION All LEDs are unlit HelpyGSM-RM not Check power supply supplied SIM card not present or Correctly insert the SIM card in not correctly inserted the dedicated location SIM card locked by PIN Enter the PIN using the code 282 code SIM card expired or Check the SIM card operation on... - Page 32 HelpyGSM-RM edition 14/12/2018 Esse-ti S.r.l. Via G. Capodaglio, 9 62019 Recanati (MC) – ITALY Tel. +39 071 7506066 Fax +39 071 7506057 www.esse-ti.it support@esse-ti.it...
Need help?
Do you have a question about the HELPY GSM-RM and is the answer not in the manual?
Questions and answers