CODELOCKS CODELOCK 300 Installation Instructions

T E M P L A T E T E M P L A T E
4 7 / "
16
(113mm)
5 1 / "
8
(107mm)
2 1 / "
8
5 / "
16 (54mm)
(8mm)
2 3 / "
8
(60mm)
2 3 / "
4
(70mm)

1. APPLY THE TEMPLATE

2. FIXING THE LOCK

Select the required backset, 2 / " (60mm) or 2 / " (70mm) and
3 3
8 4
crease along the line marked door edge and tape it to the door.
Mark the holes to be drilled according to your template. Mark the
center line of the door edge on the center line of the deadbolt.
Now apply the template to the other side of the door, aligning it
with your first mark in the middle of the door edge.
Keeping the drill level and square to the door, drill holes from
both sides to avoid splintering of the door face.

Positioning and fixing the deadbolt

Mark a central point on the 'center line of deadbolt' on the
door edge. The spring-loaded spindle will fit doors between
Mark the depth of 3 1 / " (90mm) on the drill bit with tape to act as 2 1 / " (35mm - 65mm
2
2
a visible depth limit. Drill a 1" (25mm) hole, 3 1 / " (90mm) deep, thick break off the
2
keeping the drill level and square to the door.
spindle. For doors more than
Put the deadbolt into the hole, and with the edges parallel to the
Helpline for advice. The spring keeps the spindle firmly
door, draw around the face plate. engaged in the outside handle when the lock is assembled
Remove the deadbolt. Score the outline with a Stanley Knife to on the door.
avoid splitting prior to chiselling a 1 / " (3mm) deep rebate to fit
8 Insert the spindle, with the spring on the code side, through
the faceplate flush to the door.
the 2 1
Insert deadbolt with arrow pointing up, fix with the wood screws.
engages the deadbolt correctly for the hand of the door
Cut the fixing bolts to suit the door thickness, allowing at
least one but not more than two threaded sections to enter
the lock case.
Using the fixing bolts, screw front and back plates together
through the door as per the diagram with gaskets in place.
Before final tightening make sure that the lock is vertical,
and test the mechanism ensure that it is all moving easily.
DO NOT CLOSE THE DOOR UNTIL YOU ARE SURE THAT
THE CODE WORKS. DO NOT
as this may cause distortion and lead to poor operation.

3. FITTING THE KEEP PLATE

Position the keep plate on
the frame so that it lines up
with the deadbolt.
Mark the inner and outer
1
edges of the keep plate
3
and cut a rebate so that it
fits flush with the surface of
the door frame.
Drill or cut a recess 1
Fit the keeper plate using only one wood screw at first to
4
ensure that it is positioned accurately. The deadbolt should
enter the aperture easily. When satisifed secure the keep
2
with remaining screws.
1 3 / " and
8
) thick. For doors less than 2 " (50mm)
15mm) section at the end of the
5 / " (
8
2 / " ( 65mm) thick, ring the
1
2
/ " (54mm" ) hole in the door, and make sure that it
8
over tighten the fixing bolts
INSTALLATION INSTRUCTIONS
" (25mm) deep for the deadbolt.
Mortise Deadbolt
with Key Override
Helpline, service & spares
TOLL FREE 1 877 263 3562
CODELOCKS INC - US
Tel +1 714 9792900
Fax +1 714 9792902
sales@codelocks.co.us
www.codelocks.us
CODELOCKS LTD - UK
Tel +44 (0)1635 239645
Fax +44 (0)1635 239644
sales@codelocks.co.uk
www.codelocks.com