Table of Contents
Advertisement
Installation
Instructions
ISTEP 51 LEVEL REFRIGERATOR
All models have 4-point leveling. The thmt is
supported
by leveling
legs,
the
rear
is supported
by
a_!justable
wheels.
Both
are
accessible
fl'om
the
fl'ont
of the
refligerator.
• To level
the
back
of the
refligerator,
turn
the
7/16"
hex
nut
located
above
the
fl'ont
wheels.
Turn
clockwise
to raise
or com_terclockwise
to lower
the
refl'igerator.
• For
fl'ont
leveling,
use a ]-1/4"
open-end
wrench.
• A(!just
height
of refl'igerator
to match
installation
cutout
opening
83-1/2"
to 84-1/2".
The refligerator
should
be
level
and
phunb
with
cabinetry.
/[
I
Hex Nut Adjusts_]
Rear Whei__eg
CAUTION:
The
rear
leveling
wheels
and
fl'ont
leveling
legs
are
limited
to a maximum
height
ac!justment
of 1". If the
installation
requires
more
than
84-1/2"
height,
the
installer
should
elew_te
the
refl'igerator
on a sheet
of pl}_vood
or rtmners.
Cabinetry
trim
could
also
be
added
across
the
top
of the
opening
to shorten
the
opening.
If you
attempt
to raise
the
refrigerator
more
thm_
1", you
will dmnage
the
front
leveling
legs
and
the
rear leveling
wheels.
PRUDENCE
I.es
roues
de nivellement
artiste
et les pattes
de
nivellement
avant
permettent
un
r_glage
maximal
de
25 mm
(l po).
Si l'ouverture
pore"
le r_fi'ig_ratem"
a tree
hauteur
sup_rieure
_'l 2,15
m
(84-1/2
po),
l'installatem"
doit
_lever
le r_li'ig_ratem"
sur
une
feuille
de
contre-plaqu6
ou
des
glissi&res,
ll est
_galement
possible
d'ajouter
des
baguettes
de
finition
des
placards
sur
le haut
de
l'ouverture
afin
de la r_duire.
Lever
le r&frig&rateur
de
plus
de
25 Inln (1 po)
endommage
les pattes
de nivellement
avant
et les roues
de
_fivellement
arri&re.
I STEP 61 ALTERNATE ANTI-TIP
PROCEDURE
The
refrigerator
must
be
secured
to prevent
tipping.
The
mlti-tip
brackets
cmmot
be
used
on metal
wall
studs.
Use
this Alternate
Procedure
to secure
the
refrigerator
against
tip-over
whenever
metal
wall
studs
are
encountered
mad there
is no
soffit.
Side View
Top Case Trim
i
i
=
!
!
!
Install Four
1-1/2" DrywallScrews
ThroughTrimand IntoSoffit
or 3/4" Min. Wood Brace
• Raise the grille panel
to access
case trim.
• Use a 3/16"
bit to drill tour
evenly
spaced
clearance
holes
through
the metal
top case trim.
• Use a 1/16"
bit to drill to pilot holes
through
the
metal
clearance
holes and
into
the wood sottit,
The
holes
should
be centered
in the sottit or a 3/4"
rain.
wood brace.
The
brace
spanning
the enclosm'e
must
be secm'elv
tastened
to cabinets
on both
sides.
• Install
flmr, 1-1/2"
drywall
screws into
the pilot holes.
13
Advertisement
Table of Contents
