Table of Contents
Advertisement
Installation
Instructions
ISTEP 11REMOVE PACKAGING
CAUTI0N:
Relrigerator
is much
hea, ier at the
top than
at the botton/
- be careflll
when
moxing
X4hen
usim* a hand
track,
handle
fl'om side onE.
PRUDENCE: i,e
be...,.p
plus hmrd
en haut
qu'en
bas. ll taut 6tre prudent
lots
des d_placements.
Si tm diable
est utilis_,
il taut
soulexer
le r_frig&'atetu
_sur le c'6t_ seulement.
• Careflflly
cut banding
at the top and bottom,
reulove
otffer carton.
• Slide out back
corner
posts
(2).
• Slide carton
off top of cabinet.
NOTE: IT IS NOT
NE(:ESSARY
TO lAY CABINET
DOWN
IN ORDER
TO REMOVE
SKID!
• The
unit is secured
to the skid with 4 slotted
tie-down
straps.
Remove
the timr
5/16"
bolts
fl'om
the base channels
in the tie-downs.
J
• Remoxe
the fore" 7/16"
bolts
secm'ing
the straps
to the skid.
CAUTION: DoNOS
ATTEMPT
TO ROI,I,
UNIT
OFF SKID.
Remove
PRUDENCE: n,NE
TieDowns FAUT PAS ESSAYER DE
EMRE
ROUI,ER
I,E
--,"
I_d_FRIGt_RATEUI
_. POUR
%
I,'ENI,EVER
DE lAY
PA1,ETTE.
• Support
blocks
on the bottom
of the refl'igeration
case must
be removed
befi)re
the refl'igerator
is
taken
off the skid or damage
will occm'. Careflflly;
tilt refl'igerator
and slide blocks
out from
beneath.
• Remove
toekick,
set aside fin" final installation.
• I.ifl the refl{gerator
off the skid with an appliance
dolly. Handle
fl'om
the sides.
[STEP 2] INSTALL WATER LINE
• A cold water
SUl_ply is required
fin" automatic
icemaker
operation.
The water
pressure
must
be
between
40 and
190 p.s.i.
• Route
l/4"
OD COl)per or GE SmartConnect
'_
plastic
tubing
between
house
cold water
line and
the water connection
location.
• Tubing
should
be long
enough
to extend
to the
fl'ont
of the refl'igeratm:
Allow enough
tubing
to
accommodate
bend
leading
into the water line
connection.
NOTE:
The
only GE approved
plastic
tubing
is
sui)plied
in the GE SmartConnect
TM
Refl'igerator
Tubing
kits. Do not use any other
plastic
water sui)ply
line because
the line is trader
pressure
at all times.
Other
types of plastic
Inav crack
or IUI)ture
with age
_lll(1
Catlse
water
dalnage
to VO/lI" houle.
GE SmartConnect
"_Refl'igerator
Tubing
Kits are
available
in the fi_llowing
lengths:
2' (.6 m)
WXO8XIO002
6' (1.8 m)
WXO8XIO006
15' (4.6 m)
X,_3XO8XIO015
25' (7.6 m)
X,_3XO8XlO025
Copper Tubing A'
Shut off the main
water supply.
Turn
on the nearest
taucet
long enough
to clear
the
line of water.
• Install a shut-off
valve between
the icelnaker
water
valve and
cold water pipe
in a basement
or cabinet.
The shut-off
wflve should
be located
where
it will
be easily accessible.
• Turn
on the main
water
SUl)ply and flush
debris.
Run about
a quart
of water
through
the tubing
into
a bucket.
Shut off water
sui)ply at the shut-off
wflve.
NOTE: Saddle
tyi)e shut-off
wflves are included
in
many water
sui)ply
kits. Befln'e
pro'chasing,
make
stu'e a saddle
type wflve complies
with yore" local
plmnbing
codes.
NOTE: Commonwealth
of Massachusetts
Plmnbing
Codes
948CMR
shall be adhered
to. Saddle
valves
are illegal
and
use is not permitted
in Massachusetts.
Consult
with wmr licensed
phunber.
11
Advertisement
Table of Contents
